Land Rover Serie II Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Land Rover Serie II
The Land Rover Series II Military is an off-road vehicle produced from 1962 to 1971 by British manufacturer Land Rover. It was the replacement for the aging Land Rover Series I. The vehicle came in two different wheelbases, the 88 inch and 109 inch, which are commonly referred to as SWB and LWB respectively. Due to their extreme off-road capabilities these vehicles were extensively used for military purposes. The Series II was the first vehicle to use the well-known 2.25-litre petrol engine, although the first 1,500 or so short wheelbase (SWB) models retained the 52 hp (39 kW) 2.0-litre petrol engine from the Series I. This larger petrol engine produced 72 hp (54 kW) and was closely related to the 2.0-litre diesel unit still in use.Land Rover Serie II FAQ's
How do I bleed the brakes in a Land Rover Serie II?
Bleeding the brakes in a Land Rover Serie II is necessary when air has entered the brake lines, resulting in spongy or ineffective braking. Start by identifying the brake bleeder valves on each wheel. Begin with the wheel farthest from the master cylinder and attach a clear plastic hose to the bleeder valve. Place the other end of the hose into a container partially filled with brake fluid to prevent air from being sucked back into the system. With the help of an assistant, slowly pump the brake pedal several times and hold it down. Open the bleeder valve to release the air and fluid, then close the valve before releasing the brake pedal. Repeat this process until all air bubbles are eliminated and only clean fluid is flowing through the hose.
How do I change the oil in a Land Rover Serie II?
To change the oil in a Land Rover Serie II, first, locate the oil drain plug underneath the vehicle. Use a wrench to remove the plug and drain the old oil into a container. Once drained, replace the drain plug and refill the engine with the recommended amount and type of oil specified in the Land Rover Serie II automotive repair manual.
How do I check the brake fluid level in a Land Rover Serie II?
To check the brake fluid level in a Land Rover Serie II, locate the brake fluid reservoir under the hood. The reservoir has a clear plastic housing, allowing you to easily see the fluid level. Ensure the vehicle is on a level surface and the engine is cool before removing the reservoir cap and checking the fluid level. If the fluid is below the recommended level, consult the automotive repair manual to determine the correct type of brake fluid to add.
How do I check the transmission fluid in a Land Rover Serie II?
Checking the transmission fluid in a Land Rover Serie II requires the vehicle to be running and at operating temperature. Locate the transmission dipstick, usually located near the back of the engine bay. With the engine running, pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again. Check the fluid level indicated on the dipstick against the recommended range in the automotive repair manual. If the fluid is low or discolored, it may be necessary to add or replace the transmission fluid.
How do I diagnose a starting issue in a Land Rover Serie II?
If a Land Rover Serie II has trouble starting, there are several potential causes that can be diagnosed using the automotive repair manual. Check the battery for proper voltage and connections, inspect the ignition system for faulty spark plugs or ignition coils, verify the fuel system for clogged filters or a malfunctioning fuel pump, and examine the starter motor and associated wiring for any issues. The repair manual will provide detailed troubleshooting steps and diagnostic procedures to help identify the specific problem.
How do I replace a headlight bulb in a Land Rover Serie II?
To replace a headlight bulb in a Land Rover Serie II, first, locate the back of the headlight assembly under the hood. Depending on the model year, there may be a cover or connector that needs to be removed to access the bulb. Once accessed, carefully detach the old bulb by twisting it counterclockwise and remove it from the socket. Insert the new bulb and secure it by twisting it clockwise. Finally, reattach any covers or connectors that were removed.
How do I replace the alternator in a Land Rover Serie II?
To replace the alternator in a Land Rover Serie II, begin by disconnecting the negative terminal of the battery to prevent electrical shocks. Locate the alternator, usually mounted on the engine block, and detach the electrical connectors and wiring harnesses connected to it. Loosen and remove the mounting bolts or adjuster bracket holding the alternator in place. Carefully remove the old alternator and install the new one, ensuring proper alignment and
How do I replace the fuel filter in a Land Rover Serie II?
To replace the fuel filter in a Land Rover Serie II, first, locate the filter, which is typically found along the fuel line between the fuel tank and the engine. Relieve the fuel system pressure by disconnecting the fuel pump fuse or relay and cranking the engine until it stalls. Once the pressure is relieved, use a wrench or socket to disconnect the fuel lines from the filter. Remove the old filter and replace it with a new one, ensuring the flow direction is correct. Reconnect the fuel lines and reinstall the fuel pump fuse or relay.
How do I replace the serpentine belt in a Land Rover Serie II?
To replace the serpentine belt in a Land Rover Serie II, locate the belt tensioner pulley and use a wrench or socket to relieve tension on the belt. Slide the old belt off the pulleys and carefully route the new belt around the pulleys, following the correct path as indicated in the automotive repair manual. Once the belt is properly aligned, release the tensioner pulley to apply tension to the belt. Finally, visually inspect the belt to ensure it is properly seated on all pulleys and running smoothly.
How do I replace the spark plugs in a Land Rover Serie II?
To replace the spark plugs in a Land Rover Serie II, begin by disconnecting the negative terminal of the battery to prevent accidental electrical discharge. Locate the spark plug wires or ignition coils, depending on the specific engine configuration. Remove the wires or coils to access the spark plugs. Use a spark plug socket and ratchet to carefully remove the old spark plugs and replace them with new ones, ensuring they are properly gapped according to the specifications in the automotive repair manual. Reconnect the spark plug wires or ignition coils and reconnect the battery.
How do I replace the thermostat in a Land Rover Serie II?
To replace the thermostat in a Land Rover Serie II, begin by draining the coolant from the radiator into a suitable container. Locate the thermostat housing, usually connected to the engine block, and remove the bolts or clamps securing it. Carefully remove the old thermostat and gasket, ensuring no debris falls into the engine. Install the new thermostat and gasket, making sure it is properly aligned and seated. Reattach the thermostat housing using the appropriate torque specifications provided in the automotive repair manual. Finally, refill the radiator with the correct type and amount of coolant.
How do I replace the water pump in a Land Rover Serie II?
To replace the water pump in a Land Rover Serie II, start by draining the coolant from the radiator into a suitable container. Locate the water pump, usually driven by the engine's accessory belt, and remove any components obstructing access to it. Disconnect the hoses and electrical connectors connected to the water pump. Unbolt and remove the old water pump, ensuring to clean the mounting surface before installing the new pump. Apply a suitable gasket sealant, if required, and install the new water pump, tightening the bolts to the specified torque. Reconnect the hoses and electrical connectors, refill the radiator with coolant, and check for any leaks.
How do I troubleshoot an electrical issue in a Land Rover Serie II?
When faced with an electrical issue in a Land Rover Serie II, the automotive repair manual provides a systematic approach to troubleshoot the problem. First, check the fuse box for any blown fuses related to the affected systems. Inspect the wiring harnesses for any damage or loose connections. Utilize a multimeter to test the electrical components for continuity and proper voltage. If necessary, refer to the wiring diagrams provided in the repair manual to trace the circuit and identify any potential faults. Following these steps will help diagnose and resolve electrical issues in a Land Rover Serie II.
How often should I change the air filter in a Land Rover Serie II?
The air filter in a Land Rover Serie II should be changed regularly according to the maintenance schedule outlined in the automotive repair manual. Generally, it is recommended to replace the air filter every 12,000 to 15,000 miles or annually, whichever comes first. However, if the vehicle is driven in dusty or off-road conditions, more frequent air filter changes may be necessary.
What is the recommended tire pressure for a Land Rover Serie II?
The recommended tire pressure for a Land Rover Serie II can be found in the automotive repair manual. It is important to follow these recommendations to ensure optimal performance and safety. Overinflated or underinflated tires can affect the vehicle's handling, fuel efficiency, and tire wear.
Get notified for new manuals?
We'll send you a quick email when a new Land Rover Serie II manual is added.
There are currently no manuals available for Land Rover Serie II at this time.