Mercedes ML 400 Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Mercedes ML 400
The Mercedes-Benz M-Class (or ML-Class) is a mid-size luxury sport utility vehicle (SUV), introduced in 1997 as a 1998 model, and built by the German automaker Mercedes-Benz. Gradually, the M-Class became a sales success in the United States and Mexico. ML 400 is a five-door sport utility vehicle manufactured between 2001 and 2005. It is available as rear-wheel or front-wheel drive. It is produced with 3,996 cc diesel engines. This model s engine can produce power of 184 kW. Car is available with manual and automatic transmission style. The GLE-Class name will be used in 2015 for the forthcoming facelifted Mercedes-Benz M-Class.
Mercedes ML 400 FAQ's
How do I change the oil in a Mercedes ML 400?
To change the oil in a Mercedes ML 400, you will need to locate the oil drain plug underneath the vehicle and remove it to drain the old oil. Once drained, replace the drain plug and remove the oil filter using an oil filter wrench. Install a new oil filter and fill the engine with the recommended amount and type of oil as specified in the owner's manual.
How do I check the coolant level in a Mercedes ML 400?
To check the coolant level in a Mercedes ML 400, ensure that the engine is cool before opening the hood. Locate the coolant reservoir, usually marked with a "coolant" or "antifreeze" label. The coolant level should be between the minimum and maximum marks on the reservoir. If the level is low, add a mixture of coolant and distilled water in the recommended ratio as specified in the owner's manual. Avoid opening the radiator cap when the engine is hot to prevent injury.
How do I check the transmission fluid level in a Mercedes ML 400?
To check the transmission fluid level in a Mercedes ML 400, start the engine and let it warm up to operating temperature. Locate the transmission dipstick, usually marked with a yellow handle, and remove it. Wipe the dipstick clean, reinsert it fully, and then remove it again to read the fluid level. Ensure that the fluid level is within the recommended range as indicated on the dipstick, and add fluid if necessary.
How do I jump-start a Mercedes ML 400?
To jump-start a Mercedes ML 400, park a functioning vehicle with the engine off close to the dead vehicle, making sure both vehicles are in park or neutral. Connect the positive (red) jumper cable to the positive terminal of the dead battery, and then connect the other end of the positive cable to the positive terminal of the functioning battery. Connect the negative (black) cable to the negative terminal of the functioning battery, and then attach the other end of the negative cable to an unpainted metal surface on the dead vehicle, away from the battery. Start the functioning vehicle and let it run for a few minutes before attempting to start the dead vehicle.
How do I program a key for a Mercedes ML 400?
To program a key for a Mercedes ML 400, insert an existing working key into the ignition and turn it to the "on" position without starting the engine. Within 10 seconds, remove the key and insert the new key you want to program. Turn the new key to the "on" position within 10 seconds and wait for at least 5 seconds. The new key should now be programmed and ready to use.
How do I replace a battery in a Mercedes ML 400?
To replace a battery in a Mercedes ML 400, start by turning off the vehicle and ensuring all electrical accessories are switched off. Open the hood and locate the battery, usually in the engine compartment. Disconnect the negative (black) cable followed by the positive (red) cable from the battery terminals, using a wrench or pliers. Remove any securing brackets or clamps holding the battery in place, and then carefully lift out the old battery. Install the new battery in the correct position, reconnect the positive cable followed by the negative cable, and ensure they are securely tightened.
How do I replace a brake light bulb in a Mercedes ML 400?
To replace a brake light bulb in a Mercedes ML 400, open the trunk or liftgate and locate the bulb housing on the rear of the vehicle. Twist the bulb housing counterclockwise to remove it and access the bulb. Gently remove the old bulb and insert the new one, ensuring it is properly seated. Finally, twist the bulb housing back into place and test the brake lights to ensure proper functioning.
How do I replace a cabin air filter in a Mercedes ML 400?
To replace a cabin air filter in a Mercedes ML 400, locate the filter housing, which is usually located behind the glove compartment or under the dashboard. Open the housing by releasing the latches or removing the screws, depending on the design. Take out the old filter and replace it with a new one, ensuring it is properly aligned. Close the housing and secure it in place. It is recommended to refer to the owner's manual for specific instructions and illustrations.
How do I replace a headlight bulb in a Mercedes ML 400?
To replace a headlight bulb in a Mercedes ML 400, you will need to access the headlight assembly from under the hood. Locate the back of the headlight assembly and twist the bulb socket counterclockwise to remove it. Pull out the old bulb and insert the new one, making sure it is properly aligned. Finally, twist the bulb socket back into place and test the headlights to ensure proper functioning.
How do I replace a serpentine belt in a Mercedes ML 400?
To replace a serpentine belt in a Mercedes ML 400, locate the belt tensioner, which is usually a pulley with a square hole for a ratchet or breaker bar. Insert the ratchet or breaker bar into the square hole and rotate it counterclockwise to relieve tension on the belt. Slide the belt off the pulleys, taking note of the routing for installation of the new belt. Install the new belt by following the correct routing and rotating the tensioner counterclockwise again to allow the belt to be slipped onto the pulleys. Ensure the belt is properly seated on all pulleys before releasing the tensioner.
How do I replace a spark plug in a Mercedes ML 400?
To replace a spark plug in a Mercedes ML 400, ensure the engine is cool before starting. Locate the spark plug wires or coil packs, and remove them one by one, making note of their order if necessary. Use a spark plug socket and ratchet to remove the old spark plug, and inspect it for any signs of damage or wear. Install the new spark plug, ensuring it is properly tightened, and then reconnect the spark plug wire or coil pack. Repeat the process for each spark plug.
How do I replace a windshield wiper blade in a Mercedes ML 400?
To replace a windshield wiper blade in a Mercedes ML 400, lift the wiper arm away from the windshield until it locks into a raised position. Locate the release tab or button on the wiper blade attachment point and press or pull it to detach the old blade. Attach the new wiper blade by inserting it into the attachment point until it clicks into place. Gently lower the wiper arm back onto the windshield.
How do I reset the service indicator in a Mercedes ML 400?
To reset the service indicator in a Mercedes ML 400, insert the key into the ignition and turn it to the "on" position without starting the engine. Use the steering wheel buttons to navigate to the "Settings" menu, then scroll down to "Service." Select "Reset" and confirm the action. The service indicator should now be reset, and the next service interval will be displayed accordingly.
How often should I replace the air filter in a Mercedes ML 400?
The air filter in a Mercedes ML 400 should typically be replaced every 20,000 to 30,000 miles, or as recommended by the manufacturer. However, if you frequently drive in dusty or dirty conditions, it may be necessary to replace the air filter more frequently. Regularly inspect the air filter for dirt and debris accumulation, and replace it if it appears clogged or dirty to ensure optimum engine performance and fuel efficiency.
What is the recommended tire pressure for a Mercedes ML 400?
The recommended tire pressure for a Mercedes ML 400 typically varies depending on the specific model and the size of the tires. However, it is generally recommended to maintain a tire pressure between 32-35 PSI for optimal performance and safety. You can find the recommended tire pressure specific to your vehicle in the owner's manual or on the tire placard located on the driver's side door jamb.
Get notified for new manuals?
We'll send you a quick email when a new Mercedes ML 400 manual is added.