Austin Ambassador Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Austin Ambassador
The Austin Ambassador is a large family car that was introduced by Austin in March 1982. The vehicle was a heavily updated version of the Princess, an aging model that had lacked a hatchback.Only the doors and inner structure were carried over, but the wedge-shaped side profile betrayed the car's Princess origins, and it was not considered a truly new model. The Princess had been out of production for four months by the time that the Ambassador went on sale.To some extent a competitor to smaller-engined models of the Austin Rover Group's own Rover SD1, sales were low and the model was discontinued in 1984.
Austin Ambassador FAQ's
How do I bleed the brakes on an Austin Ambassador?
To bleed the brakes on an Austin Ambassador, first, locate the brake bleed valve on each brake caliper. Then, attach a clear hose to the valve and submerge the other end in a container of brake fluid. Next, have a helper press the brake pedal while you open and close the bleed valve to remove any air from the brake lines. Finally, repeat this process on each brake caliper until all the air has been removed from the brake system.
How do I change the oil in an Austin Ambassador?
To change the oil in an Austin Ambassador, first, warm up the engine by running it for a few minutes. Then, locate the oil drain plug and remove it to drain the old oil into a pan. Once the old oil has drained, replace the drain plug and add the recommended amount of new oil to the engine. Finally, check the oil level and top up if necessary.
How do I check the transmission fluid level in an Austin Ambassador?
To check the transmission fluid level in an Austin Ambassador, first, ensure that the engine is warm and idling. Then, locate the transmission dipstick and remove it from the transmission. Wipe it clean, reinsert it, and then remove it again to check the fluid level.
How do I replace the air filter on an Austin Ambassador?
To replace the air filter on an Austin Ambassador, first, remove the old air filter from the air filter housing. Then, clean out any debris or dirt that may have accumulated in the housing. Next, insert the new air filter into the housing and make sure it is securely in place. Finally, close the air filter housing and start the engine to ensure that it is running properly.
How do I replace the alternator on an Austin Ambassador?
To replace the alternator on an Austin Ambassador, first, disconnect the battery to prevent any electrical shocks. Then, remove the drive belt from the alternator and the mounting bolts that hold the alternator in place. Next, remove the old alternator from the car and replace it with a new one. Finally, reattach the drive belt and the mounting bolts.
How do I replace the battery on an Austin Ambassador?
To replace the battery on an Austin Ambassador, first, locate the battery and remove the negative cable from the battery. Then, remove the positive cable from the battery. Next, remove the old battery from the car and replace it with a new one. Finally, reconnect the cables to the new battery, starting with the positive cable.
How do I replace the brake pads on an Austin Ambassador?
To replace the brake pads on an Austin Ambassador, first, jack up the car and remove the wheels. Then, remove the brake caliper and the old brake pads. Next, install the new brake pads and reattach the brake caliper. Finally, replace the wheels and lower the car back down to the ground.
How do I replace the fuel filter on an Austin Ambassador?
To replace the fuel filter on an Austin Ambassador, first, locate the fuel filter and remove the fuel lines from it. Then, remove the old fuel filter from the car and replace it with a new one. Finally, reattach the fuel lines to the new fuel filter and start the engine to check that it is running smoothly.
How do I replace the radiator on an Austin Ambassador?
To replace the radiator on an Austin Ambassador, first, drain the coolant from the engine by removing the drain plug. Then, disconnect the hoses that connect the radiator to the engine. Next, remove the mounting bolts that hold the radiator in place and remove the old radiator from the car. Finally, install the new radiator and reattach the hoses and mounting bolts.
How do I replace the thermostat on an Austin Ambassador?
To replace the thermostat on an Austin Ambassador, first, locate the thermostat housing and remove the bolts that hold it in place. Then, remove the old thermostat from the housing and replace it with a new one. Finally, reattach the housing to the engine and fill the coolant system with fresh coolant.
How do I replace the timing belt on an Austin Ambassador?
To replace the timing belt on an Austin Ambassador, first, remove the timing belt cover and the old timing belt. Next, make sure that the timing marks on the engine are aligned before installing the new timing belt. Finally, replace the timing belt cover and start the engine to check that it is running smoothly.
How do I replace the water pump on an Austin Ambassador?
To replace the water pump on an Austin Ambassador, first, drain the coolant from the engine by removing the drain plug. Then, remove the hoses that connect the water pump to the engine. Next, remove the mounting bolts that hold the water pump in place and remove the old water pump from the car. Finally, install the new water pump and reattach the hoses and mounting bolts.
How do I troubleshoot an engine that won't start on an Austin Ambassador?
If an engine won't start on an Austin Ambassador, first, check the battery to make sure it is fully charged. Next, check the spark plugs to see if they are fouled or worn. Finally, check the fuel system to ensure that the fuel pump is working properly and that there are no clogged fuel lines.
How often should I replace the spark plugs on an Austin Ambassador?
The spark plugs on an Austin Ambassador should be replaced every 30,000 miles or every 3 years, whichever comes first. This is because the spark plugs can become worn or fouled over time, which can lead to poor engine performance. Replacing the spark plugs at the recommended intervals will help ensure that the engine runs smoothly.
What is the recommended oil type for an Austin Ambassador?
The recommended oil type for an Austin Ambassador is 20W-50 engine oil. This type of oil is ideal for use in the Austin Ambassador's engine as it provides excellent protection against wear and tear. It is also designed to maintain its viscosity in high temperatures, which is important for the engine's performance.
Get notified for new manuals?
We'll send you a quick email when a new Austin Ambassador manual is added.
There are currently no manuals available for Austin Ambassador at this time.
Related Models
Austin A35 | Austin A40 |