Proton 400 Serie Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Proton 400 Serie
The Proton Wira, also as known as the Proton 400 Series, is a car manufactured by Malaysian carmaker Proton. It was produced in four-door saloon and five-door hatchback guises and is based on the Mitsubishi Lancer platform. Proton made minor changes to the taillights, bumpers, and dashboard. 5 trim levels were available. The 1.6 and 1.8L model (4G92/4G93) were equipped with rear disc brakes, front and rear armrests, electric mirrors, folding rear seats, electric windows on all doors, and a high quality interior. Proton redesigned the saloon to make a 5-door hatchback variant during the mid-1990s, basing the car on the saloon Wira and sporting similar tail lights.Proton 400 Serie FAQ's
How do I change a flat tire on a Proton 400 Serie?
To change a flat tire on a Proton 400 Serie, first, locate the spare tire, jack, and lug wrench in the trunk of the vehicle. Use the lug wrench to loosen the lug nuts on the flat tire, then use the jack to lift the vehicle off the ground. Once the vehicle is raised, remove the lug nuts and the flat tire, replace it with the spare tire, and tighten the lug nuts securely before lowering the vehicle back to the ground.
How do I change the brake pads on a Proton 400 Serie?
To change the brake pads on a Proton 400 Serie, first, locate the brake caliper and remove the caliper bolts using a wrench or socket. Slide out the old brake pads and replace them with new ones, ensuring they are properly aligned. Reinstall the caliper bolts and tighten them securely. It is recommended to consult the manual for detailed instructions and any specific precautions.
How do I change the oil in a Proton 400 Serie?
To change the oil in a Proton 400 Serie, first, locate the oil drain plug underneath the vehicle. Use a wrench to remove the drain plug and let the old oil drain into a container. Once all the oil has drained, replace the drain plug and refill the engine with the specified amount and type of oil mentioned in the manual.
How do I check the brake fluid level in a Proton 400 Serie?
To check the brake fluid level in a Proton 400 Serie, locate the brake fluid reservoir under the hood. The reservoir is usually translucent with minimum and maximum level markings. Check that the fluid level is between these markings. If necessary, add the recommended type of brake fluid as mentioned in the manual. Take caution while handling brake fluid, as it can damage painted surfaces and should not come into contact with skin.
How do I check the engine oil level in a Proton 400 Serie?
To check the engine oil level in a Proton 400 Serie, park the vehicle on a level surface and turn off the engine. Locate the engine oil dipstick, usually marked with a bright-colored handle. Pull out the dipstick, wipe it clean, reinsert it fully, and then remove it again. The oil level should be within the designated range indicated on the dipstick. If necessary, add the recommended type and amount of oil as mentioned in the manual.
How do I check the transmission fluid level in a Proton 400 Serie?
To check the transmission fluid level in a Proton 400 Serie, start the engine and allow it to warm up to normal operating temperature. Locate the transmission dipstick, usually located near the back of the engine bay. Pull out the dipstick, wipe it clean, reinsert it fully, and then remove it again. The fluid level should be within the designated range indicated on the dipstick. If necessary, add the recommended type of transmission fluid as mentioned in the manual.
How do I replace a fuse in a Proton 400 Serie?
To replace a fuse in a Proton 400 Serie, first, locate the fuse box, which is usually found in the engine bay or interior of the vehicle. Identify the fuse that needs to be replaced by referring to the fuse box diagram in the manual. Use a fuse puller or a pair of tweezers to remove the faulty fuse and replace it with a new one of the same rating. Ensure the new fuse is securely seated in the fuse box. Consult the manual for any specific fuse replacement instructions or precautions.
How do I replace a headlight bulb on a Proton 400 Serie?
To replace a headlight bulb on a Proton 400 Serie, access the bulb housing by opening the hood or reaching behind the headlight assembly. Disconnect the electrical connector from the back of the bulb, then twist the bulb counterclockwise to remove it from the housing. Insert the new bulb into the housing and twist it clockwise to secure it. Reconnect the electrical connector and test the headlights. Refer to the manual for any specific bulb replacement instructions or precautions.
How do I replace the battery in a Proton 400 Serie?
To replace the battery in a Proton 400 Serie, first, locate the battery, usually found in the engine bay or trunk. Disconnect the negative (-) cable first, followed by the positive (+) cable. Remove any clamps or brackets securing the battery in place and carefully lift it out. Install the new battery, ensuring proper polarity, and secure it with the clamps or brackets. Finally, reconnect the positive (+) cable followed by the negative (-) cable. Consult the manual for any specific battery replacement instructions or precautions.
How do I reset the maintenance light on a Proton 400 Serie?
To reset the maintenance light on a Proton 400 Serie, turn the ignition key to the "ON" position without starting the engine. Press the accelerator pedal three times within five seconds. The maintenance light should start flashing and then turn off, indicating that it has been reset. For more detailed instructions or if the light does not reset, refer to the manual.
How often should I replace the air filter in a Proton 400 Serie?
It is generally recommended to replace the air filter in a Proton 400 Serie every 12,000 to 15,000 miles or as indicated in the maintenance schedule provided in the manual. Regularly replacing the air filter helps maintain good engine performance by ensuring clean air intake and preventing debris from entering the engine.
How often should I replace the spark plugs in a Proton 400 Serie?
The spark plugs in a Proton 400 Serie should typically be replaced every 30,000 to 45,000 miles or as indicated in the maintenance schedule provided in the manual. Regularly replacing the spark plugs ensures proper ignition and combustion, leading to optimal engine performance and fuel efficiency. Refer to the manual for the correct spark plug type and any specific replacement instructions.
What is the recommended tire pressure for a Proton 400 Serie?
The recommended tire pressure for a Proton 400 Serie is typically mentioned on the sticker located on the driver's side door jamb. It is important to maintain the correct tire pressure to ensure optimal handling, fuel efficiency, and tire life. Refer to the manual for further details regarding tire maintenance and safety.
What is the towing capacity of a Proton 400 Serie?
The towing capacity of a Proton 400 Serie can vary depending on the specific model and configuration. It is important to consult the manual for the correct towing capacity and any specific requirements or recommendations for towing trailers or other vehicles. Exceeding the recommended towing capacity can result in damage to the vehicle or compromised safety.
What type of coolant should I use in a Proton 400 Serie?
Proton 400 Serie requires a specific type of coolant as mentioned in the manual. It is important to use the recommended coolant to ensure proper engine cooling and prevent any damage caused by using an incompatible coolant. Check the manual for the correct coolant type and any specific mixing instructions.
Get notified for new manuals?
We'll send you a quick email when a new Proton 400 Serie manual is added.
There are currently no manuals available for Proton 400 Serie at this time.