Fiat Palio Workshop Manual Alarm Fitting Instructions PDF

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
fipal98gbb.doc
MAKE
FIAT
MOD.
PALIO
YEAR
98
PETROL
DIESEL
ALARM/SIREN
POSITION
Position the compact alarms and the sirens in the engine compartment, on the
column of the shock absorber, passengers side.To pass the cables open the
plastic bulkhead under the windshield wiper and use the original rubber provided
of two holes whom one is free. You will find it near the fuse box.
POWER SUPPLY + 30: connect to the 3 mm
2
RED wire located in the 1 way black connector, in the
upper right part of the fuse box.
- 31: connect to the 2 mm
2
BROWN wire located in the ground point behind the
left lateral bulkhead, drivers side.
IGNITION WIRE + 15/54: connect to the 3 mm
2
ORANGE wire located in the wiring harness and
coming out of the 4 way white connector of the ignition key.
DIRECTION INDICATORS
Connect to the 1,5 mm
2
BLUE and BLUE/BLACK wires located in the wiring
harness and coming out of the multiway white connector in the fuse box, the first
in the upper front part of the fuse box.
ELECTRIC WINDOWS Positive control signal
Front window, driver’s side:
cut the 2 mm
2
WHITE/RED wire.
Front window, passenger’s side:
cut the 2 mm
2
RED/GREEN wire.
Connections are made directly in the wiring harness coming out of the original
switches.
CENTRAL DOORS LOCKING Negative control signal
Connect to the 1,5 mm
2
BLUE wire (lock) and WHITE wire (unlock) located in the
wiring harness coming out of the rubber grommet of the front door, drivers side.
IMMOBILISATION POINT 1 Fuel pump
Cut the 1,5 mm
2
BROWN/WHITE wire located in the multiway white connector,
the first on the left of the fuse box.
IMMOBILISATION POINT 2 +15 general
cut the 3 mm
2
ORANGE wire located in the wiring harness and coming out of the
3 way white connector of the ignition key.
BONNET SWITCH
Install an additional switch on the front headlamp support plate, near the original
bonnet stop rubber.
DOORS SWITCH
Connect to the 1 mm
2
WHITE/BLUE wire located in the wiring harness of the 3
way grey connector and coming out of the courtesy lamp.
BOOT SWITCH
Connect to the 1 mm
2
WHITE/RED wire located in the wiring harness of the 2 way
grey connector that comes out of the boots interior lamp.
X

Summary of Content

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00www.cobra.itNote: This information is not binding, therefore it must be considered only an example for installation purposes that must be executedas per the instructions given on the product installation manual.fipal98gbb.docMAKEFIATMOD.PALIOYEAR98 PETROLDIESELALARM/SIRENPOSITIONPosition the compact alarms and the sirens in the engine compartment, on thecolumn of the shock absorber, passengers side.To pass the cables open theplastic bulkhead under the windshield wiper and use the original rubber providedof two holes whom one is free. You will find it near the fuse box.POWER SUPPLY + 30: connect to the 3 mm2 RED wire located in the 1 way black connector, in theupper right part of the fuse box.- 31: connect to the 2 mm2 BROWN wire located in the ground point behind theleft lateral bulkhead, drivers side.IGNITION WIRE + 15/54: connect to the 3 mm2 ORANGE wire located in the wiring harness andcoming out of the 4 way white connector of the ignition key.DIRECTION INDICATORSConnect to the 1,5 mm2 BLUE and BLUE/BLACK wires located in the wiringharness and coming out of the multiway white connector in the fuse box, the firstin the upper front part of the fuse box.ELECTRIC WINDOWS Positive control signalFront window, drivers side:cut the 2 mm2 WHITE/RED wire.Front window, passengers side:cut the 2 mm2 RED/GREEN wire.Connections are made directly in the wiring harness coming out of the originalswitches.CENTRAL DOORS LOCKING Negative control signalConnect to the 1,5 mm2 BLUE wire (lock) and WHITE wire (unlock) located in thewiring harness coming out of the rubber grommet of the front door, drivers side.IMMOBILISATION POINT 1 Fuel pumpCut the 1,5 mm2 BROWN/WHITE wire located in the multiway white connector,the first on the left of the fuse box.IMMOBILISATION POINT 2 +15 generalcut the 3 mm2 ORANGE wire located in the wiring harness and coming out of the3 way white connector of the ignition key.BONNET SWITCHInstall an additional switch on the front headlamp support plate, near the originalbonnet stop rubber.DOORS SWITCHConnect to the 1 mm2 WHITE/BLUE wire located in the wiring harness of the 3way grey connector and coming out of the courtesy lamp.BOOT SWITCHConnect to the 1 mm2 WHITE/RED wire located in the wiring harness of the 2 waygrey connector that comes out of the boots interior lamp.X