Jaguar X Type 2004 Misc Document Remote Transmitter Programming PDF

Date of issue 12/04 Bulletin Number XT501-23 Page 1 of 2
DATE
XT501-2312/04
SERVICE
TECHNICAL BULLETIN
Remote Transmitter Programming –
Alternate Method Without WDS –
Procedure
2002 MY-ON
X-TYPE
C00001-ON
MODEL
VIN
X-TYPE
NOTE: THE INFORMATION IN TECHNICAL BULLETINS IS INTENDED FOR USE BY TRAINED, PROFESSIONAL TECHNI-
CIANS WITH THE KNOWLEDGE, TOOLS, AND EQUIPMENT TO DO THE JOB PROPERLY AND SAFELY. IT INFORMS
THESE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR PROVIDES INFORMATION THAT
COULD ASSIST IN PROPER VEHICLE SERVICE. THE PROCEDURES SHOULD NOT BE PERFORMED BY “DO-IT-
YOURSELFERS.” DO NOT ASSUME THAT A CONDITION DESCRIBED AFFECTS YOUR CAR. CONTACT A JAGUAR
DEALER TO DETERMINE WHETHER THE BULLETIN APPLIES TO YOUR VEHICLE.
Issue:
This Technical Bulletin provides an alternate procedure for programming the remote
transmitters.
The Worldwide Diagnostic System (WDS) is not required to carry out remote transmitter
programming.
Action:
To program the remote transmitter(s) without using WDS, follow the procedure outlined
below.
Note: When carrying out the alarm remote programming, ensure that
no other vehicles within a 50 meter radius are undergoing the same
programming procedure, as this could affect the programming
operation.
Note: All required remote transmitters must be available when
carrying out this procedure.
1. Open driver’s door.
2. Turn the ignition switch to the ‘auxiliary’ position, then turn the ignition switch to the
‘ON’ position and back to the ‘auxiliary’ position four times.
Note: A chime from the Generic Electronic Module (GEM) will indicate
programming status has been enabled.
3. Turn the ignition switch to ‘OFF’ position.
4. Remove the key from the ignition switch.
5. To program the transmitter, press any key within 10 seconds.
Note: If the remote transmitter has been accepted, the GEM will
make a chime.

Jaguar X Type 2004 Misc Document Remote Transmitter Programming Summary of Content

Date of issue 12/04 Bulletin Number XT501-23 Page 1 of 2DATEXT501-2312/04SERVICETECHNICAL BULLETINRemote Transmitter Programming Alternate Method Without WDS Procedure2002 MY-ONX-TYPEC00001-ONMODELVINX-TYPENOTE: THE INFORMATION IN TECHNICAL BULLETINS IS INTENDED FOR USE BY TRAINED, PROFESSIONAL TECHNI-CIANS WITH THE KNOWLEDGE, TOOLS, AND EQUIPMENT TO DO THE JOB PROPERLY AND SAFELY. IT INFORMSTHESE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR PROVIDES INFORMATION THATCOULD ASSIST IN PROPER VEHICLE SERVICE. THE PROCEDURES SHOULD NOT BE PERFORMED BY DO-IT-YOURSELFERS. DO NOT ASSUME THAT A CONDITION DESCRIBED AFFECTS YOUR CAR. CONTACT A JAGUARDEALER TO DETERMINE WHETHER THE BULLETIN APPLIES TO YOUR VEHICLE.Issue:This Technical Bulletin provides an alternate procedure for programming the remotetransmitters.The Worldwide Diagnostic System (WDS) is not required to carry out remote transmitterprogramming.Action:To program the remote transmitter(s) without using WDS, follow the procedure outlinedbelow.Note: When carrying out the alarm remote programming, ensure thatno other vehicles within a 50 meter radius are undergoing the sameprogramming procedure, as this could affect the programmingoperation.Note: All required remote transmitters must be available whencarrying out this procedure.1. Open drivers door.2. Turn the ignition switch to the auxiliary position, then turn the ignition switch to theON position and back to the auxiliary position four times.Note: A chime from the Generic Electronic Module (GEM) will indicateprogramming status has been enabled.3. Turn the ignition switch to OFF position.4. Remove the key from the ignition switch.5. To program the transmitter, press any key within 10 seconds.Note: If the remote transmitter has been accepted, the GEM willmake a chime.