Jeep Grand Cherokee XJ Workshop Manual 1995 (6) PDF

ELECTRICAL
GROUP INDEX
Group Group
AUDIO SYSTEMS ........................ 8F
BATTERY/STARTER/GENERATOR SERVICE .... 8B
BATTERY/STARTING/CHARGING SYSTEMS
DIAGNOSTICS ......................... 8A
CHIME/BUZZER WARNING SYSTEMS ........ 8U
HORNS ................................ 8G
IGNITION SYSTEMS ...................... 8D
INSTRUMENT PANEL AND GAUGES ......... 8E
LAMPS ................................ 8L
OVERHEAD CONSOLE .................... 8C
POWER LOCKS .......................... 8P
POWER MIRRORS ....................... 8T
POWER SEATS .......................... 8R
POWER WINDOWS ....................... 8S
REAR WINDOW DEFOGGER ............... 8N
RESTRAINT SYSTEMS ................... 8M
TURN SIGNAL AND HAZARD WARNING
SYSTEMS ............................. 8J
VEHICLE SPEED CONTROL SYSTEM ......... 8H
WIPER AND WASHER SYSTEMS ............ 8K
XJ WIRING DIAGRAMS-LEFT HAND DRIVE ... 8W
XJ WIRING DIAGRAMS-RIGHT HAND DRIVE . 8W
YJ WIRING DIAGRAMS .................. 8W
BATTERY/STARTING/CHARGING SYSTEMS DIAGNOSTICS
CONTENTS
page page
BATTERY ............................... 2
CHARGING SYSTEM ..................... 17
IGNITION-OFF DRAW .................... 10
SPECIFICATIONS ........................ 23
STARTING SYSTEM ...................... 11
USING ON-BOARD DIAGNOSTIC SYSTEM .... 22
GENERAL INFORMATION
The battery, starting, and charging systems operate
with one another; therefore, they must be tested as a
complete system. In order for the vehicle to start and
charge properly, all of the components involved in
these systems must perform within specifications.
Group 8A covers battery, starting (Fig. 1) and
charging (Fig. 2) system diagnostic procedures. These
procedures include the most basic conventional diag-
nostic methods, to On-Board Diagnostics (OBD) built
into the Powertrain Control Module (PCM). Use of an
induction milliamp ammeter, volt/ohmmeter, battery
charger, carbon pile rheostat (load tester), and 12-
volt test lamp will be required.
All OBD-sensed systems are monitored by the
PCM. Each monitored circuit is assigned a Diagnos-
tic Trouble Code (DTC). The PCM will store a DTC in
electronic memory for any failure it detects. See Us-
ing On-Board Diagnostic System in this group for
more information.
J ELECTRICAL 8A - 1

Jeep Grand Cherokee XJ Workshop Manual 1995 (6) Summary of Content

ELECTRICALGROUP INDEXGroup GroupAUDIO SYSTEMS ........................ 8FBATTERY/STARTER/GENERATOR SERVICE .... 8BBATTERY/STARTING/CHARGING SYSTEMSDIAGNOSTICS ......................... 8ACHIME/BUZZER WARNING SYSTEMS ........ 8UHORNS ................................ 8GIGNITION SYSTEMS ...................... 8DINSTRUMENT PANEL AND GAUGES ......... 8ELAMPS ................................ 8LOVERHEAD CONSOLE .................... 8CPOWER LOCKS .......................... 8PPOWER MIRRORS ....................... 8TPOWER SEATS .......................... 8RPOWER WINDOWS ....................... 8SREAR WINDOW DEFOGGER ............... 8NRESTRAINT SYSTEMS ................... 8MTURN SIGNAL AND HAZARD WARNINGSYSTEMS ............................. 8JVEHICLE SPEED CONTROL SYSTEM ......... 8HWIPER AND WASHER SYSTEMS ............ 8KXJ WIRING DIAGRAMS-LEFT HAND DRIVE ... 8WXJ WIRING DIAGRAMS-RIGHT HAND DRIVE . 8WYJ WIRING DIAGRAMS .................. 8WBATTERY/STARTING/CHARGING SYSTEMS DIAGNOSTICSCONTENTSpage pageBATTERY ............................... 2CHARGING SYSTEM ..................... 17IGNITION-OFF DRAW .................... 10SPECIFICATIONS ........................ 23STARTING SYSTEM ...................... 11USING ON-BOARD DIAGNOSTIC SYSTEM .... 22GENERAL INFORMATIONThe battery, starting, and charging systems operatewith one another; therefore, they must be tested as acomplete system. In order for the vehicle to start andcharge properly, all of the components involved inthese systems must perform within specifications.Group 8A covers battery, starting (Fig. 1) andcharging (Fig. 2) system diagnostic procedures. Theseprocedures include the most basic conventional diag-nostic methods, to On-Board Diagnostics (OBD) builtinto the Powertrain Control Module (PCM). Use of aninduction milliamp ammeter, volt/ohmmeter, batterycharger, carbon pile rheostat (load tester), and 12-volt test lamp will be required.All OBD-sensed systems are monitored by thePCM. Each monitored circuit is assigned a Diagnos-tic Trouble Code (DTC). The PCM will store a DTC inelectronic memory for any failure it detects. See Us-ing On-Board Diagnostic System in this group formore information.J ELECTRICAL 8A - 1