Mitsubishi L400 Workshop Manuals and Repair Manuals

Every Manual available online - found by our community and shared for FREE. Enjoy!

Mitsubishi L400

The Mitsubishi Delica is a popular range of trucks and MPVs from Japanese manufacturer Mitsubishi since 1968. The fourth generation Delica, also known as the Mitsubishi Space Gear in Japan and Mitsubishi Starwagon in Australia is primarily called the L400. With four-wheel drive and based on Mitsubishi Pajero s chassis, the L400 had full off-road capabilities. This vehicle was available as both cargo version and passenger version with five different body styles. The fourth generation Delica is based on the chassis of the Mitsubishi Pajero[citation needed] and has full off road capabilities, with four-wheel drive, high and low ratio gears and differential locking. It has engine variations from 2.5 liters through to a 2.8-liter intercooled turbodiesel.

Mitsubishi L400 FAQ's

How do I bleed the brakes in a Mitsubishi L400?

To bleed the brakes in a Mitsubishi L400, start with the wheel furthest from the master cylinder (usually the rear passenger side). Have a helper pump the brake pedal several times and hold it down while you open the bleeder valve on the brake caliper or wheel cylinder. Allow the brake fluid and any air bubbles to escape, then close the valve. Repeat this process for each wheel, moving progressively closer to the master cylinder. Ensure the brake fluid reservoir is topped up throughout the bleeding process to avoid introducing air into the system.

How do I change the brake pads in a Mitsubishi L400?

To change the brake pads in a Mitsubishi L400, start by loosening the lug nuts on the wheel of the brake pads you want to replace. Then, jack up the vehicle and remove the wheel. Locate the brake caliper and remove the bolts securing it. Carefully remove the caliper, take out the old brake pads, and install the new ones. Finally, reassemble the caliper, mount the wheel, and tighten the lug nuts.

How do I change the cabin air filter in a Mitsubishi L400?

To change the cabin air filter in a Mitsubishi L400, locate the filter housing, which is usually located behind the glove compartment or under the dashboard. Open the housing by removing the clips or screws securing it. Take out the old filter and replace it with a new one, ensuring it is properly aligned and fits snugly. Finally, reattach the housing and secure it with the clips or screws.

How do I check the engine oil level in a Mitsubishi L400?

To check the engine oil level in a Mitsubishi L400, park the vehicle on a level surface and ensure the engine is turned off. Locate the engine oil dipstick, usually located near the front of the engine. Pull out the dipstick, wipe it clean with a cloth, reinsert it fully, and then pull it out again to check the oil level. The oil level should be between the minimum and maximum marks on the dipstick.

How do I check the transmission fluid in a Mitsubishi L400?

To check the transmission fluid in a Mitsubishi L400, start the engine and allow it to reach operating temperature. Park the vehicle on a level surface and engage the parking brake. Locate the transmission dipstick, usually near the back of the engine compartment. Pull out the dipstick, wipe it clean, reinsert it fully, and then pull it out again to check the fluid level. The fluid should be within the designated range on the dipstick.

How do I replace a headlight bulb in a Mitsubishi L400?

To replace a headlight bulb in a Mitsubishi L400, locate the headlight assembly at the front of the vehicle. Depending on the specific model year, you may need to access the bulb from inside the engine compartment or behind the headlight assembly. Disconnect the electrical connector, remove the retaining clip or cover, and carefully remove the old bulb. Insert the new bulb, ensuring it is securely in place, and reassemble the components. Test the headlight to ensure it is functioning correctly.

How do I replace a serpentine belt in a Mitsubishi L400?

To replace a serpentine belt in a Mitsubishi L400, locate the belt routing diagram, usually found under the hood or in the vehicle's manual. Use a wrench or tensioner tool to relieve tension on the belt by rotating the tensioner pulley in the appropriate direction. Slide the old belt off the pulleys and carefully install the new belt, following the correct routing as indicated by the diagram. Finally, release the tensioner to apply proper tension to the new belt.

How do I replace the fuel filter in a Mitsubishi L400?

To replace the fuel filter in a Mitsubishi L400, locate the filter, which is typically located along the fuel line, near the fuel tank or engine compartment. Ensure the engine is turned off and relieve fuel pressure by either removing the fuel pump fuse or disconnecting the fuel pump relay. Disconnect the fuel lines from the filter, being cautious of any fuel spillage. Remove the old filter and install the new one, ensuring proper alignment and connection of the fuel lines. Finally, reattach the fuel pump fuse or relay, and check for any fuel leaks.

How do I reset the maintenance required light in a Mitsubishi L400?

To reset the maintenance required light in a Mitsubishi L400, turn the ignition switch to the "ON" position without starting the engine. Within a few seconds, locate and press the "TRIP" or "MODE" button on the instrument cluster repeatedly until the maintenance required light disappears. Some models may require different button combinations, so it is essential to consult the vehicle's manual for the specific resetting procedure.

How do I test the alternator in a Mitsubishi L400?

To test the alternator in a Mitsubishi L400, start the engine and allow it to reach operating temperature. Using a voltmeter, connect the positive lead to the positive terminal of the battery and the negative lead to the negative terminal. With the engine running, observe the voltage reading on the voltmeter. A properly functioning alternator should output around 13.5 to 14.5 volts. If the reading is significantly lower or higher, it may indicate a faulty alternator that requires further inspection or replacement.

How often should I change the air filter in a Mitsubishi L400?

The air filter in a Mitsubishi L400 should be checked and replaced regularly. It is generally recommended to inspect the air filter every 12,000 miles or 12 months, whichever comes first. However, this frequency may vary depending on driving conditions. If the air filter appears dirty or clogged, it should be replaced to ensure optimal engine performance and fuel efficiency.

How often should I replace the timing belt in a Mitsubishi L400?

The timing belt in a Mitsubishi L400 should typically be replaced every 60,000 to 100,000 miles or as recommended by the manufacturer. It is crucial to consult the vehicle's manual or a professional mechanic to determine the specific replacement interval for your model year. Neglecting to replace the timing belt at the recommended intervals can lead to engine damage and costly repairs.

What is the recommended oil viscosity for a Mitsubishi L400?

The recommended oil viscosity for a Mitsubishi L400 can vary depending on factors such as the climate and driving conditions. However, as a general guideline, a multi-grade oil with a viscosity of 5W-30 or 10W-30 is commonly used. It is important to refer to the vehicle's manual or consult with a professional to determine the most suitable oil viscosity for optimal engine performance and protection.

What is the recommended tire pressure for a Mitsubishi L400?

The recommended tire pressure for a Mitsubishi L400 can vary depending on factors such as the vehicle's load and driving conditions. However, as a general guideline, the tire pressure is typically around 32 PSI (pounds per square inch) for both the front and rear tires. It is crucial to refer to the vehicle's manual or the tire placard located on the driver's side door jamb for the exact tire pressure specifications.

What type of coolant should I use in a Mitsubishi L400?

It is recommended to use a high-quality ethylene glycol-based coolant with a mixture of 50% coolant and 50% distilled water in a Mitsubishi L400. This coolant should meet the specifications outlined in the vehicle's manual or by the manufacturer. Ensure that the coolant is compatible with the engine's material, such as aluminum or cast iron, to prevent any potential damage or corrosion.

Mitsubishi L400 Manuals Index

Mitsubishi L400 Workshop Manual

Mitsubishi L400 Misc Document

Related Models