Nissan 350Z Workshop Manual 2003 (9) PDF | Page 65

TROUBLE DIAGNOSIS
BRC-65
[TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
OFF: Approximately 1 second after the ignition switch is turned on (when system is normal), when TCS function is not operat-
ing
Flash: When the TCS function is operating during driving.
Note 5: A/T model.
Note 6: M/T vehicle is UNKWN.
CONSULT- II Functions AFS000YU
CAUTION:
? Do not use the ?function test? for diagnosis. For more information, refer to the separate volume
?CONSULT-II OPERATION MANUAL (Function Test)?.
? When communicating with CONSULT-II, the ABS warning lamp and TCS OFF indicator lamp are
on. When communication has been broken off, the SLIP indicator lamp will flash for about 1 sec.
? When TCS conducts a self-diagnosis, data monitoring, or executes the active test function, EBD,
ABS, and TCS control are not conducted.
? When a self-diagnosis, active test, work support, etc., of the TCS/ABS control unit is conducted
using CONSULT-II, stop engine temporarily and connect CONSULT-II and then select ?TCS/ABS?.
? CONSULT-II self-diagnosis results are displayed without regard to occurrence timing. In some
cases later ones (timing value is small) appear on the next screen.
CONSULT-II FUNCTION APPLICATION TABLE (MAIN ITEMS)
: Applicable
?: Not applicable
Items Self-diagnosis Data monitor Active test
FR RH WHEEL SENSOR ?
FR LH WHEEL SENSOR ?
RR RH WHEEL SENSOR ?
RR LH WHEEL SENSOR ?
Stop lamp switch x ?
FR RH IN ABS SOL
FR RH OUT ABS SOL
FR LH IN ABS SOL
FR LH OUT ABS SOL
RR RH IN ABS SOL
RR RH OUT ABS SOL
RR LH IN ABS SOL
RR LH OUT ABS SOL
ABS ACTUATOR RELAY ?
ABS motor relay ?
ABS warning lamp ? ?
Battery voltage ?
TCS/ABS C/U ??
ABS motor
CAN communication ?
Engine speed signal ? ?
Gear ? ?
TCS OFF switch ? ?
TCS OFF indicator lamp ? ?
SLIP indicator lamp ? ?
Throttle position ? ?
Position signal ? ?

Nissan 350Z Workshop Manual 2003 (9) Summary of Content

TROUBLE DIAGNOSISBRC-65[TCS/ABS]CDEGHIJKLMABBRCOFF: Approximately 1 second after the ignition switch is turned on (when system is normal), when TCS function is not operat-ingFlash: When the TCS function is operating during driving.Note 5: A/T model.Note 6: M/T vehicle is UNKWN.CONSULT- II Functions AFS000YUCAUTION: Do not use the function test for diagnosis. For more information, refer to the separate volumeCONSULT-II OPERATION MANUAL (Function Test). When communicating with CONSULT-II, the ABS warning lamp and TCS OFF indicator lamp areon. When communication has been broken off, the SLIP indicator lamp will flash for about 1 sec. When TCS conducts a self-diagnosis, data monitoring, or executes the active test function, EBD,ABS, and TCS control are not conducted. When a self-diagnosis, active test, work support, etc., of the TCS/ABS control unit is conductedusing CONSULT-II, stop engine temporarily and connect CONSULT-II and then select TCS/ABS. CONSULT-II self-diagnosis results are displayed without regard to occurrence timing. In somecases later ones (timing value is small) appear on the next screen.CONSULT-II FUNCTION APPLICATION TABLE (MAIN ITEMS): Applicable: Not applicableItems Self-diagnosis Data monitor Active testFR RH WHEEL SENSOR FR LH WHEEL SENSOR RR RH WHEEL SENSOR RR LH WHEEL SENSOR Stop lamp switch x FR RH IN ABS SOL FR RH OUT ABS SOL FR LH IN ABS SOL FR LH OUT ABS SOL RR RH IN ABS SOL RR RH OUT ABS SOL RR LH IN ABS SOL RR LH OUT ABS SOL ABS ACTUATOR RELAY ABS motor relay ABS warning lamp Battery voltage TCS/ABS C/U ABS motor CAN communication Engine speed signal Gear TCS OFF switch TCS OFF indicator lamp SLIP indicator lamp Throttle position Position signal