Nissan 350Z Workshop Maunual 2004 (10) PDF | Page 9

CLUTCH MASTER CYLINDER
CL-9
D
E
F
G
H
I
J
K
L
M
A
B
CL
Revision: 2004 December 2004.5 350Z
2. Install master cylinder assembly and tighten mounting nuts to the specified torque. Refer to CL-8,
"Removal and Installation" .
3. Using a flare nut torque wrench, tighten clutch tube flare nut to the specified torque. Refer to CL-12,
"Removal and Installation" .
4. Install clevis to the clutch pedal, and fix clevis with clevis pin.
5. Install snap pin to the clevis pin.
6. Install reservoir hose to the nipple. Install the reservoir tank to the vehicle, and then tighten mounting nuts
to the specified torque.
7. After completing this procedure, inspect and adjust pedal height
and then bleed the clutch tube. Refer to CL-5, "
On-Vehicle
Inspection and Adjustment" and CL-7, "Bleeding" .
8. Install hoodledge cover.
9. Install instrument driver panel lower. Refer to IP-11, "
Removal
and Installation" .
10. Install dash side finisher. Refer to IP-11, "
Removal and Installa-
tion" .
11. Install footrest.Refer to EI-43, "
FLOOR TRIM" .
12. Install kicking plate. Refer to EI-37, "
Removal and Installation (for Roadster Models)" .
Disassembly and Assembly ACS004N3
DISASSEMBLY
1. Using a pin punch, remove spring pin, nipple and reservoir seal
from the cylinder body.
2. Loosen push rod lock nut. Remove clevis and lock nut.
3. Remove the seat from the cylinder body.
4. Remove the stopper ring and stopper, and then remove the
push rod, piston assembly, and return spring from the cylinder
body.
CAUTION:
Restrain the push rod while doing this because there is a
danger the piston assembly will fly out of the cylinder body.
: 5.8 NĚm (0.59 Kg-m, 51 in-lb)
SCIA1587E
Tool number : Commercial service tool
PCIB0274E

Nissan 350Z Workshop Maunual 2004 (10) Summary of Content

CLUTCH MASTER CYLINDERCL-9DEFGHIJKLMABCLRevision: 2004 December 2004.5 350Z2. Install master cylinder assembly and tighten mounting nuts to the specified torque. Refer to CL-8,"Removal and Installation" .3. Using a flare nut torque wrench, tighten clutch tube flare nut to the specified torque. Refer to CL-12,"Removal and Installation" .4. Install clevis to the clutch pedal, and fix clevis with clevis pin.5. Install snap pin to the clevis pin.6. Install reservoir hose to the nipple. Install the reservoir tank to the vehicle, and then tighten mounting nutsto the specified torque.7. After completing this procedure, inspect and adjust pedal heightand then bleed the clutch tube. Refer to CL-5, "On-VehicleInspection and Adjustment" and CL-7, "Bleeding" .8. Install hoodledge cover.9. Install instrument driver panel lower. Refer to IP-11, "Removaland Installation" .10. Install dash side finisher. Refer to IP-11, "Removal and Installa-tion" .11. Install footrest.Refer to EI-43, "FLOOR TRIM" .12. Install kicking plate. Refer to EI-37, "Removal and Installation (for Roadster Models)" .Disassembly and Assembly ACS004N3DISASSEMBLY1. Using a pin punch, remove spring pin, nipple and reservoir sealfrom the cylinder body.2. Loosen push rod lock nut. Remove clevis and lock nut.3. Remove the seat from the cylinder body.4. Remove the stopper ring and stopper, and then remove thepush rod, piston assembly, and return spring from the cylinderbody.CAUTION:Restrain the push rod while doing this because there is adanger the piston assembly will fly out of the cylinder body.: 5.8 Nm (0.59 Kg-m, 51 in-lb)SCIA1587ETool number : Commercial service tool PCIB0274E