Nissan 350Z Workshop Maunual 2004 (9) PDF | Page 29

TROUBLE DIAGNOSIS
BRC-29
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
Revision: 2004 December 2004.5 350Z
Inspection 1 Wheel Sensor System AFS00298
INSPECTION PROCEDURE
After using the CONSULT-II SELF-DIAG RESULTS to determine the location of the malfunctioning wheel sen-
sor, check all areas to determine the component to be replaced.
CAUTION:
? Do not measure the resistance value and also voltage between the sensor terminal with tester etc.,
because the sensor is an active sensor.
? Do not expand the terminal of the connector with a/the tester terminal stick, when it does the
inspection with the tester.
1. TIRE INSPECTION
Check air pressure, wear, and size.
Are the air pressure, wear, and size within the standard values?
YES >> GO TO 2.
NO >> Adjust air pressure, or replace tire.
2. SENSOR AND SENSOR ROTOR INSPECTION
? Check the condition of the sensor mount (for looseness, etc.).
? Check the surface of the front sensor rotor rubber for damage.
? Check the rear sensor rotor for damage.
OK or NG
OK >> GO TO 3.
NG >> Repair the sensor mount or replace the sensor rotor.
3. SELF-DIAGNOSIS RESULT CHECK
Check self-diagnosis results.
Is the above displayed in the self-diagnosis display items?
YES >> GO TO 4.
NO >> Inspection End
4. CONNECTOR INSPECTION
1. Disconnect ABS control unit connector and the malfunctioning wheel sensor connector E42 (FR - LH) or
E27 (FR - RH) or T5 (RR - RH, LH). Check the terminal to see if it is deformed, disconnected, loose, etc.,
and replace it if any non-standard condition is found.
2. Reconnect the connector, drive at a speed of approximately 30 km/h (19 MPH) or more for approximately
1 minute, and conduct self-diagnosis.
OK or NG
OK >> The connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 5.
Self-diagnosis results
FR RH SENSOR -1, -2
FR LH SENSOR-1, - 2
RR RH SENSOR-1, -2
RR LH SENSOR-1, -2

Nissan 350Z Workshop Maunual 2004 (9) Summary of Content

TROUBLE DIAGNOSISBRC-29[ABS]CDEGHIJKLMABBRCRevision: 2004 December 2004.5 350ZInspection 1 Wheel Sensor System AFS00298INSPECTION PROCEDUREAfter using the CONSULT-II SELF-DIAG RESULTS to determine the location of the malfunctioning wheel sen-sor, check all areas to determine the component to be replaced.CAUTION: Do not measure the resistance value and also voltage between the sensor terminal with tester etc.,because the sensor is an active sensor. Do not expand the terminal of the connector with a/the tester terminal stick, when it does theinspection with the tester.1. TIRE INSPECTIONCheck air pressure, wear, and size.Are the air pressure, wear, and size within the standard values?YES GO TO 2.NO Adjust air pressure, or replace tire.2. SENSOR AND SENSOR ROTOR INSPECTION Check the condition of the sensor mount (for looseness, etc.). Check the surface of the front sensor rotor rubber for damage. Check the rear sensor rotor for damage.OK or NGOK GO TO 3.NG Repair the sensor mount or replace the sensor rotor.3. SELF-DIAGNOSIS RESULT CHECKCheck self-diagnosis results.Is the above displayed in the self-diagnosis display items?YES GO TO 4.NO Inspection End4. CONNECTOR INSPECTION1. Disconnect ABS control unit connector and the malfunctioning wheel sensor connector E42 (FR - LH) orE27 (FR - RH) or T5 (RR - RH, LH). Check the terminal to see if it is deformed, disconnected, loose, etc.,and replace it if any non-standard condition is found.2. Reconnect the connector, drive at a speed of approximately 30 km/h (19 MPH) or more for approximately1 minute, and conduct self-diagnosis.OK or NGOK The connector terminal contact is loose, damaged, open or shorted.NG GO TO 5.Self-diagnosis resultsFR RH SENSOR -1, -2FR LH SENSOR-1, - 2RR RH SENSOR-1, -2RR LH SENSOR-1, -2