Nissan 350Z Workshop Maunual 2005 (15) PDF | Page 112

EM-112
CAMSHAFT
Revision: 2005 August 2005 350Z
INSPECTION AFTER INSTALLATION
Inspection of Camshaft Sprocket (INT) Oil Groove
CAUTION:
? Perform this inspection only when DTC P0011 or P0021 are detected in self-diagnostic results of
CONSULT-II and it is directed according to inspection procedure of EC section. Refer to EC-96,
"TROUBLE DIAGNOSIS" .
? Check when engine is cold so as to prevent burns from any splashing engine oil.
1. Check the engine oil level. Refer to LU-8, "
ENGINE OIL" .
2. Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a. Release fuel pressure. Refer to EC-94, "
FUEL PRESSURE RELEASE" .
b. Disconnect ignition coil and injector harness connectors.
3. Remove intake valve timing control solenoid valve. Refer to EM-102, "CAMSHAFT" .
4. Crank the engine, and then make sure that engine oil comes out
from camshaft bracket (No. 1) oil hole. End crank after checking.
WARNING:
Be careful not to touch rotating parts (drive belts, idler pul-
ley, and crankshaft pulley, etc.).
CAUTION:
Engine oil may squirt from intake valve timing control sole-
noid valve installation hole during cranking. Use a shop
cloth to prevent the engine components and the vehicle. Do
not allow engine oil to get on rubber components such as
drive belt or engine mount insulators. Immediately wipe off
any splashed engine oil.
? Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does not
come out from camshaft bracket (No. 1) oil hole. Refer to LU-4, "
LUBRICATION SYSTEM" .
5. Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT),
and then check each oil groove for clogging.
? Clean oil groove if necessary. Refer to LU-4, "LUBRICATION SYSTEM" .
6. After inspection, install removed parts.
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
? Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-12, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
? Use procedure below to check for fuel leakage.
? Turn ignition switch ?ON? (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
? Start engine. With engine speed increased, check again for fuel leakage at connection points.
? Run engine to check for unusual noise and vibration.
? Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
? Bleed air from lines and hoses of applicable lines, such as in cooling system.
? After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
PBIC2869E

Nissan 350Z Workshop Maunual 2005 (15) Summary of Content

EM-112CAMSHAFTRevision: 2005 August 2005 350ZINSPECTION AFTER INSTALLATIONInspection of Camshaft Sprocket (INT) Oil GrooveCAUTION: Perform this inspection only when DTC P0011 or P0021 are detected in self-diagnostic results ofCONSULT-II and it is directed according to inspection procedure of EC section. Refer to EC-96,"TROUBLE DIAGNOSIS" . Check when engine is cold so as to prevent burns from any splashing engine oil.1. Check the engine oil level. Refer to LU-8, "ENGINE OIL" .2. Perform the following procedure so as to prevent the engine from being unintentionally started whilechecking.a. Release fuel pressure. Refer to EC-94, "FUEL PRESSURE RELEASE" .b. Disconnect ignition coil and injector harness connectors.3. Remove intake valve timing control solenoid valve. Refer to EM-102, "CAMSHAFT" .4. Crank the engine, and then make sure that engine oil comes outfrom camshaft bracket (No. 1) oil hole. End crank after checking.WARNING:Be careful not to touch rotating parts (drive belts, idler pul-ley, and crankshaft pulley, etc.).CAUTION:Engine oil may squirt from intake valve timing control sole-noid valve installation hole during cranking. Use a shopcloth to prevent the engine components and the vehicle. Donot allow engine oil to get on rubber components such asdrive belt or engine mount insulators. Immediately wipe offany splashed engine oil. Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does notcome out from camshaft bracket (No. 1) oil hole. Refer to LU-4, "LUBRICATION SYSTEM" .5. Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT),and then check each oil groove for clogging. Clean oil groove if necessary. Refer to LU-4, "LUBRICATION SYSTEM" .6. After inspection, install removed parts.Inspection for LeaksThe following are procedures for checking fluids leak, lubricates leak and exhaust gases leak. Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than requiredquantity, fill to the specified level. Refer to MA-12, "RECOMMENDED FLUIDS AND LUBRICANTS" . Use procedure below to check for fuel leakage. Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuelleakage at connection points. Start engine. With engine speed increased, check again for fuel leakage at connection points. Run engine to check for unusual noise and vibration. Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluidsincluding engine oil and engine coolant. Bleed air from lines and hoses of applicable lines, such as in cooling system. After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to thespecified level, if necessary.PBIC2869E