Nissan 350Z Workshop Maunual 2005 (15) PDF | Page 124

EM-124
CYLINDER HEAD
Revision: 2005 August 2005 350Z
e. Turn all bolts 90 to 95 degrees clockwise [target: 90 degrees
(angle tightening)].
CAUTION:
Check the tightening angle by using angle wrench [SST].
Avoid judgment by visual inspection without tool.
? Check tightening angle indicated on angle wrench [SST] indi-
cator plate.
f. Turn all bolts 90 to 95 degrees clockwise again [target: 90
degrees (angle tightening)].
4. After installing cylinder head, measure distance between front
end faces of cylinder block and cylinder head (left and right
banks).
? If the measured value is out of the standard, re-install cylinder
head.
5. Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.
? Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-12, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
? Use procedure below to check for fuel leakage.
? Turn ignition switch ?ON? (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
? Start engine. With engine speed increased, check again for fuel leakage at connection points.
? Run engine to check for unusual noise and vibration.
? Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.
? Bleed air from lines and hoses of applicable lines, such as in cooling system.
? After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
PBIC0888E
Standard : 14.1 - 14.9 mm (0.555 - 0.587 in)
EMQ0662D
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases ? Leakage ?

Nissan 350Z Workshop Maunual 2005 (15) Summary of Content

EM-124CYLINDER HEADRevision: 2005 August 2005 350Ze. Turn all bolts 90 to 95 degrees clockwise [target: 90 degrees(angle tightening)].CAUTION:Check the tightening angle by using angle wrench [SST].Avoid judgment by visual inspection without tool. Check tightening angle indicated on angle wrench [SST] indi-cator plate.f. Turn all bolts 90 to 95 degrees clockwise again [target: 90degrees (angle tightening)].4. After installing cylinder head, measure distance between frontend faces of cylinder block and cylinder head (left and rightbanks). If the measured value is out of the standard, re-install cylinderhead.5. Install in the reverse order of removal after this step.INSPECTION AFTER INSTALLATIONInspection for LeaksThe following are procedures for checking fluids leak, lubricates leak and exhaust gases leak. Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than requiredquantity, fill to the specified level. Refer to MA-12, "RECOMMENDED FLUIDS AND LUBRICANTS" . Use procedure below to check for fuel leakage. Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuelleakage at connection points. Start engine. With engine speed increased, check again for fuel leakage at connection points. Run engine to check for unusual noise and vibration. Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluidsincluding engine oil and engine coolant. Bleed air from lines and hoses of applicable lines, such as in cooling system. After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to thespecified level, if necessary.Summary of the inspection items:* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.PBIC0888EStandard : 14.1 - 14.9 mm (0.555 - 0.587 in) EMQ0662DItem Before starting engine Engine running After engine stoppedEngine coolant Level Leakage LevelEngine oil Level Leakage LevelOther oils and fluid* Level Leakage LevelFuel Leakage Leakage LeakageExhaust gases Leakage