Nissan 350Z Workshop Maunual 2005 (15) PDF | Page 158

EM-158
CYLINDER BLOCK
Revision: 2005 August 2005 350Z
Inspection After Disassembly ABS009Z3
NOTE:
To identify 35
th
Anniversary, refer to GI-52, "Application Item" .
CRANKSHAFT END PLAY
? Measure the clearance between thrust bearings and crankshaft
arm when crankshaft is moved fully forward or backward with
dial indicator.
? If the measured value exceeds the limit, replace thrust bearings,
and measure again. If it still exceeds the limit, replace crank-
shaft also.
CONNECTING ROD SIDE CLEARANCE
? Measure the side clearance between connecting rod and crank-
shaft arm with feeler gauge.
? If the measured value exceeds the limit, replace connecting rod,
and measure again. If it still exceeds the limit, replace crank-
shaft also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
Measure the inner diameter of piston pin hole with inside microme-
ter.
Piston Pin Outer Diameter
Measure the outer diameter of piston pin with micrometer.
Piston to Piston Pin Oil Clearance
(Piston to piston pin oil clearance) = (Piston pin hole diameter) ? (Piston pin outer diameter)
Standard : 0.10 - 0.25 mm (0.0039 - 0.0098 in)
Limit : 0.30 mm (0.0118 in)
EMQ0196D
Standard : 0.20 - 0.35 mm (0.0079 - 0.0138 in)
Limit : 0.40 mm (0.0157 in)
PBIC0815E
Standard : 21.993 - 22.005 mm (0.8659 - 0.8663 in)
PBIC0116E
Standard : 21.989 - 22.001 mm (0.8657 - 0.8662 in)
PBIC0117E

Nissan 350Z Workshop Maunual 2005 (15) Summary of Content

EM-158CYLINDER BLOCKRevision: 2005 August 2005 350ZInspection After Disassembly ABS009Z3NOTE:To identify 35th Anniversary, refer to GI-52, "Application Item" .CRANKSHAFT END PLAY Measure the clearance between thrust bearings and crankshaftarm when crankshaft is moved fully forward or backward withdial indicator. If the measured value exceeds the limit, replace thrust bearings,and measure again. If it still exceeds the limit, replace crank-shaft also.CONNECTING ROD SIDE CLEARANCE Measure the side clearance between connecting rod and crank-shaft arm with feeler gauge. If the measured value exceeds the limit, replace connecting rod,and measure again. If it still exceeds the limit, replace crank-shaft also.PISTON TO PISTON PIN OIL CLEARANCEPiston Pin Hole DiameterMeasure the inner diameter of piston pin hole with inside microme-ter.Piston Pin Outer DiameterMeasure the outer diameter of piston pin with micrometer.Piston to Piston Pin Oil Clearance(Piston to piston pin oil clearance) = (Piston pin hole diameter) (Piston pin outer diameter)Standard : 0.10 - 0.25 mm (0.0039 - 0.0098 in)Limit : 0.30 mm (0.0118 in)EMQ0196DStandard : 0.20 - 0.35 mm (0.0079 - 0.0138 in)Limit : 0.40 mm (0.0157 in)PBIC0815EStandard : 21.993 - 22.005 mm (0.8659 - 0.8663 in)PBIC0116EStandard : 21.989 - 22.001 mm (0.8657 - 0.8662 in)PBIC0117E