Nissan 350Z Workshop Maunual 2005 (15) PDF | Page 33

OIL PAN AND OIL STRAINER
EM-33
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August 2005 350Z
d. Apply a continuous bead of liquid gasket with tube presser [SST:
WS39930000 ( ? )] to the cylinder block mating surface of
oil pan (upper) to a limited portion as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "
RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS" .
CAUTION:
? For bolt holes with marks (5 locations), apply liquid
gasket outside the holes.
? Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-
ter to area ?A?.
? Attaching should be done within 5 minutes after coating.
e. Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both oil pan gasket and O-rings.
? Tighten mounting bolts in numerical order as shown in the fig-
ure.
? There are two types of mounting bolts. Refer to the following
for locating bolts.
f. Tighten transmission joint bolts. Refer to MT-18, "
TRANSMISSION ASSEMBLY" (M/T models) or AT-272,
"TRANSMISSION ASSEMBLY" (A/T models).
2. Install oil strainer to oil pump.
3. Install baffle plate.
? Apply locking sealant to the thread of mounting bolts.
Use Genuine High Strength Thread Locking Sealant or equivalent. Refer to GI-47, "
RECOM-
MENDED CHEMICAL PRODUCTS AND SEALANTS" .
4. Install oil pan (lower) as follows:
a. Use scraper to remove old liquid gasket from mating surfaces.
? Also remove old liquid gasket from mating surface of oil pan
(upper).
? Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
PBIC2300E
M8 100 mm (3.97 in) : 5, 7, 8, 11
M8 25 mm (0.98 in) : Except the above
PBIC0783E
SEM958F

Nissan 350Z Workshop Maunual 2005 (15) Summary of Content

OIL PAN AND OIL STRAINEREM-33CDEFGHIJKLMAEMRevision: 2005 August 2005 350Zd. Apply a continuous bead of liquid gasket with tube presser [SST:WS39930000 ( )] to the cylinder block mating surface ofoil pan (upper) to a limited portion as shown in the figure.Use Genuine RTV Silicone Sealant or equivalent. Refer toGI-47, "RECOMMENDED CHEMICAL PRODUCTS ANDSEALANTS" .CAUTION: For bolt holes with marks (5 locations), apply liquidgasket outside the holes. Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-ter to area A. Attaching should be done within 5 minutes after coating.e. Install oil pan (upper).CAUTION:Install avoiding misalignment of both oil pan gasket and O-rings. Tighten mounting bolts in numerical order as shown in the fig-ure. There are two types of mounting bolts. Refer to the followingfor locating bolts.f. Tighten transmission joint bolts. Refer to MT-18, "TRANSMISSION ASSEMBLY" (M/T models) or AT-272,"TRANSMISSION ASSEMBLY" (A/T models).2. Install oil strainer to oil pump.3. Install baffle plate. Apply locking sealant to the thread of mounting bolts.Use Genuine High Strength Thread Locking Sealant or equivalent. Refer to GI-47, "RECOM-MENDED CHEMICAL PRODUCTS AND SEALANTS" .4. Install oil pan (lower) as follows:a. Use scraper to remove old liquid gasket from mating surfaces. Also remove old liquid gasket from mating surface of oil pan(upper). Remove old liquid gasket from the bolt holes and thread.CAUTION:Do not scratch or damage the mating surfaces when clean-ing off old liquid gasket.PBIC2300EM8 100 mm (3.97 in) : 5, 7, 8, 11M8 25 mm (0.98 in) : Except the abovePBIC0783ESEM958F