Nissan 350Z Workshop Maunual 2005 (15) PDF | Page 5

PRECAUTIONS
EM-5
C
D
E
F
G
H
I
J
K
L
M
A
EM
Revision: 2005 August 2005 350Z
? After repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust gases for leakage.
Parts Requiring Angle Tightening ABS009Y6
? Use angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of the following engine parts:
? Cylinder head bolts
? Main bearing cap bolts
? Connecting rod cap bolts
? Crankshaft pulley bolt
? Do not use a torque value for final tightening.
? The torque value for these parts are for a preliminary step.
? Ensure thread and seat surfaces are clean and coated with engine oil.
Precautions for Liquid Gasket ABS009Y7
REMOVAL OF LIQUID GASKET SEALING
? After removing mounting bolts and nuts, separate the mating
surface using seal cutter [SST] and remove old liquid gasket
sealing.
CAUTION:
Be careful not to damage the mating surfaces.
? Tap seal cutter to insert it, and then slide it by tapping on the
side as shown in the figure.
? In areas where seal cutter [SST] is difficult to use, use plastic
hammer to lightly tap the parts, to remove it.
CAUTION:
If for some unavoidable reason tool such as screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using scraper, remove old liquid gasket adhering to the gasket
application surface and the mating surface.
? Remove liquid gasket completely from the groove of the gas-
ket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to tube presser [SST: WS39930000
(?)].
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-47, "
RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS" .
4. Apply liquid gasket without breaks to the specified location with
the specified dimensions.
? If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
PBIC0002E
PBIC0003E
EMA0622D

Summary of Content

PRECAUTIONSEM-5CDEFGHIJKLMAEMRevision: 2005 August 2005 350Z After repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, andexhaust gases for leakage.Parts Requiring Angle Tightening ABS009Y6 Use angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of the following engine parts: Cylinder head bolts Main bearing cap bolts Connecting rod cap bolts Crankshaft pulley bolt Do not use a torque value for final tightening. The torque value for these parts are for a preliminary step. Ensure thread and seat surfaces are clean and coated with engine oil. Precautions for Liquid Gasket ABS009Y7REMOVAL OF LIQUID GASKET SEALING After removing mounting bolts and nuts, separate the matingsurface using seal cutter [SST] and remove old liquid gasketsealing.CAUTION:Be careful not to damage the mating surfaces. Tap seal cutter to insert it, and then slide it by tapping on theside as shown in the figure. In areas where seal cutter [SST] is difficult to use, use plastichammer to lightly tap the parts, to remove it.CAUTION:If for some unavoidable reason tool such as screwdriver isused, be careful not to damage the mating surfaces.LIQUID GASKET APPLICATION PROCEDURE1. Using scraper, remove old liquid gasket adhering to the gasketapplication surface and the mating surface. Remove liquid gasket completely from the groove of the gas-ket application surface, mounting bolts, and bolt holes.2. Wipe the liquid gasket application surface and the mating sur-face with white gasoline (lighting and heating use) to removeadhering moisture, grease and foreign materials.3. Attach liquid gasket tube to tube presser [SST: WS39930000()].Use Genuine RTV Silicone Sealant or equivalent. Refer toGI-47, "RECOMMENDED CHEMICAL PRODUCTS ANDSEALANTS" .4. Apply liquid gasket without breaks to the specified location withthe specified dimensions. If there is a groove for liquid gasket application, apply liquidgasket to the groove.PBIC0002EPBIC0003EEMA0622D