Nissan 350Z Workshop Maunual 2005 (28) PDF | Page 15

ENGINE MAINTENANCE
MA-15
C
D
E
F
G
H
I
J
K
M
A
B
MA
Revision: 2005 August 2005 350Z
ALTERNATOR AND POWER STEERING OIL PUMP BELT
1. Remove undercover with power tool.
2. Loosen idler pulley lock nut (A) and adjust tension by turning
adjusting bolt (B).
? For specified belt tension, refer to MA-14, "Checking Drive
Belts" .
3. Tighten nut (A).
A/C COMPRESSOR BELT
1. Remove undercover with power tool.
2. Loosen idler pulley lock nut (C) and adjust tension by turning adjusting bolt (D).
? For specified belt tension, refer to MA-14, "Checking Drive Belts" .
3. Tighten nut (C).
Changing Engine Coolant ALS000Q3
WARNING:
? To avoid being scalded, do not change engine coolant when engine is hot.
? Wrap a thick cloth around cap and carefully remove cap. First, turn cap a quarter of a turn to
release built-up pressure. Then turn cap all the way.
? Be careful not to allow engine coolant to contact drive belts.
DRAINING ENGINE COOLANT
1. Remove undercover with power tool.
2. Open radiator drain plug at the bottom of radiator, and then
remove radiator cap.
When drain all of engine coolant in the system, open water drain plugs on engine cylinder block.
Refer to EM-140, "
DISASSEMBLY" .
3. Remove reservoir tank as necessary, and drain engine coolant and clean tank before installing.
: 31.4 - 38.2 NĚm (3.2 - 3.9 kg-m, 24 - 28 ft-lb)
SBIA0532E
: 30.4 - 39.2 NĚm (3.1 - 4.0 kg-m, 23 - 28 ft-lb)
PBIC0893E

Nissan 350Z Workshop Maunual 2005 (28) Summary of Content

ENGINE MAINTENANCEMA-15CDEFGHIJKMABMARevision: 2005 August 2005 350ZALTERNATOR AND POWER STEERING OIL PUMP BELT1. Remove undercover with power tool.2. Loosen idler pulley lock nut (A) and adjust tension by turningadjusting bolt (B). For specified belt tension, refer to MA-14, "Checking DriveBelts" .3. Tighten nut (A).A/C COMPRESSOR BELT1. Remove undercover with power tool.2. Loosen idler pulley lock nut (C) and adjust tension by turning adjusting bolt (D). For specified belt tension, refer to MA-14, "Checking Drive Belts" .3. Tighten nut (C).Changing Engine Coolant ALS000Q3WARNING: To avoid being scalded, do not change engine coolant when engine is hot. Wrap a thick cloth around cap and carefully remove cap. First, turn cap a quarter of a turn torelease built-up pressure. Then turn cap all the way. Be careful not to allow engine coolant to contact drive belts.DRAINING ENGINE COOLANT1. Remove undercover with power tool.2. Open radiator drain plug at the bottom of radiator, and thenremove radiator cap. When drain all of engine coolant in the system, open water drain plugs on engine cylinder block.Refer to EM-140, "DISASSEMBLY" .3. Remove reservoir tank as necessary, and drain engine coolant and clean tank before installing. : 31.4 - 38.2 Nm (3.2 - 3.9 kg-m, 24 - 28 ft-lb)SBIA0532E : 30.4 - 39.2 Nm (3.1 - 4.0 kg-m, 23 - 28 ft-lb)PBIC0893E