Nissan 350Z Workshop Maunual 2005 (28) PDF | Page 23

CHASSIS AND BODY MAINTENANCE
MA-23
C
D
E
F
G
H
I
J
K
M
A
B
MA
Revision: 2005 August 2005 350Z
d. Remove A/T fluid level gauge and wipe clean with lint-free paper.
CAUTION:
When wiping away the A/T fluid level gauge, always use lint-free paper, not a cloth one.
e. Re-insert A/T fluid level gauge into A/T fluid charging pipe as far as it will go.
CAUTION:
To check fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T fluid
charging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.
f. Remove A/T fluid level gauge and note reading. If reading is at low side of range, add fluid to the A/T fluid
charging pipe.
CAUTION:
Do not overfill.
5. Drive vehicle for approximately 5 minutes in urban areas.
6. Make the fluid temperature approximately 65C (149F).
NOTE:
Fluid level will be greatly affected by temperature as shown in figure. Therefore, be certain to per-
form operation while checking data with CONSULT-II.
a. Connect CONSULT-II to data link connector.
b. Select ?MAIN SIGNALS? in ?DATA MONITOR? mode for ?A/T? with CONSULT-II.
c. Read out the value of ?ATF TEMP 1?.
7. Re-check fluid level at fluid temperatures of approximately 65C (149F) using ?HOT? range on A/T fluid
level gauge.
CAUTION:
? When wiping away the A/T fluid level gauge, always use lint-free paper, not a cloth one.
? To check fluid level, insert the A/T fluid level gauge until
the cap contacts the end of the A/T fluid charging pipe,
with the gauge reversed from the normal attachment con-
ditions as shown.
8. Check fluid condition.
? If fluid is very dark or smells burned, check operation of A/T.
Flush cooling system after repair of A/T.
? If ATF contains frictional material (clutches, bands, etc.),
replace radiator and flush cooler line using cleaning solvent
and compressed air after repair of A/T. Refer to CO-13,
"RADIATOR" and AT-14, "A/T Fluid Cooler Cleaning" .
9. Install the removed A/T fluid level gauge in the A/T fluid charging pipe.
10. Tighten the level gauge bolt.
SLIA0016E
SCIA2899E

Nissan 350Z Workshop Maunual 2005 (28) Summary of Content

CHASSIS AND BODY MAINTENANCEMA-23CDEFGHIJKMABMARevision: 2005 August 2005 350Zd. Remove A/T fluid level gauge and wipe clean with lint-free paper.CAUTION:When wiping away the A/T fluid level gauge, always use lint-free paper, not a cloth one.e. Re-insert A/T fluid level gauge into A/T fluid charging pipe as far as it will go.CAUTION:To check fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T fluidcharging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.f. Remove A/T fluid level gauge and note reading. If reading is at low side of range, add fluid to the A/T fluidcharging pipe.CAUTION:Do not overfill.5. Drive vehicle for approximately 5 minutes in urban areas.6. Make the fluid temperature approximately 65C (149F).NOTE:Fluid level will be greatly affected by temperature as shown in figure. Therefore, be certain to per-form operation while checking data with CONSULT-II.a. Connect CONSULT-II to data link connector.b. Select MAIN SIGNALS in DATA MONITOR mode for A/T with CONSULT-II.c. Read out the value of ATF TEMP 1.7. Re-check fluid level at fluid temperatures of approximately 65C (149F) using HOT range on A/T fluidlevel gauge.CAUTION: When wiping away the A/T fluid level gauge, always use lint-free paper, not a cloth one. To check fluid level, insert the A/T fluid level gauge untilthe cap contacts the end of the A/T fluid charging pipe,with the gauge reversed from the normal attachment con-ditions as shown.8. Check fluid condition. If fluid is very dark or smells burned, check operation of A/T.Flush cooling system after repair of A/T. If ATF contains frictional material (clutches, bands, etc.),replace radiator and flush cooler line using cleaning solventand compressed air after repair of A/T. Refer to CO-13,"RADIATOR" and AT-14, "A/T Fluid Cooler Cleaning" .9. Install the removed A/T fluid level gauge in the A/T fluid charging pipe.10. Tighten the level gauge bolt.SLIA0016ESCIA2899E