Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 100

BRC-100
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2005 August 2006 350Z
Note 1: Confirm tire pressure is normal.
Note 2: ON/OFF timing of ABS warning lamp
ON: Approximately 1 sec. After turning on the ignition switch or when an error is detected.
OFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal).
Note 3: ON/OFF timing of VDC OFF indicator lamp
ON: Approximately 1 sec. After the ignition switch is turned on, an error is detected, or the VDC OFF switch is on
OFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal) and the VDC OFF switch is off
Note 4: ON/OFF timing of SLIP indicator lamp
ON: Approximately 1 sec. After turning on the ignition switch or when an error is detected.
OFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal) and the VDC/TCS function is not operating
Flashing: VDC/TCS function is active during driving
CONSULT-II Functions (VDC/TCS/ABS) NFS0004A
CONSULT-II MAIN FUNCTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
M/R OUTPUT
Actuator motor and
motor relay status (ON/
OFF)
When actuator motor and
motor relay are active
(?ACTIVE TEST? with CON-
SULT-II).
ON
BRC-121, "
ABS Motor
and Motor Relay System"
When the actuator motor and
motor relay are not operating
OFF
FLUID LEV SW
Brake fluid level sen-
sor ON/OFF status
When brake fluid level sensor
is on
ON
BRC-127, "
Brake Fluid
Level Switch System"
When the brake fluid level sen-
sor is off
OFF
FAIL SIGNAL Fail signal status
During VDC fail-safe
During TCS fail-safe
During ABS fail-safe
During EBD fail-safe
ON
VDC system
TCS system
ABS system
EBD system
Monitor item Display Content
Data monitor
Reference: Inspection
item
Condition
Reference values
for normal opera-
tion
Diagnostic test mode Function Reference
WORK SUPPORT
This mode enables a technician to adjust some devices faster and more
accurately by following the indications on CONSULT-II.
BRC-83, "
Adjustment of
Steering Angle Sensor
Neutral Position"
SELF-DIAG RESULTS Self-diagnostic results can be read and erased quickly. BRC-102, "Self-Diagnosis"
DATA MONITOR
Input/Output data in the ABS actuator and electric unit (control unit) can be
read.
BRC-105, "
Data Monitor"
CAN DIAG SUPPORT
MNTR
The results of transmit/receive diagnosis of communication can be read.
LAN-15, "CAN Diagnostic
Support Monitor"
ACTIVE TEST
Diagnostic Test Mode in which CONSULT-II drives some actuators apart
from the ABS actuator and electric unit (control unit) and also shifts some
parameters in a specified range.
BRC-107, "Active Test"
FUNCTION TEST
Conducted by CONSULT-II instead of a technician to determine whether
each system is ?OK? or ?NG?.
?
ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read. ?

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

BRC-100[VDC/TCS/ABS]TROUBLE DIAGNOSISRevision: 2005 August 2006 350ZNote 1: Confirm tire pressure is normal.Note 2: ON/OFF timing of ABS warning lampON: Approximately 1 sec. After turning on the ignition switch or when an error is detected.OFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal).Note 3: ON/OFF timing of VDC OFF indicator lampON: Approximately 1 sec. After the ignition switch is turned on, an error is detected, or the VDC OFF switch is onOFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal) and the VDC OFF switch is offNote 4: ON/OFF timing of SLIP indicator lampON: Approximately 1 sec. After turning on the ignition switch or when an error is detected.OFF: Approximately 1 sec. After the ignition switch is turned on (when system is normal) and the VDC/TCS function is not operatingFlashing: VDC/TCS function is active during drivingCONSULT-II Functions (VDC/TCS/ABS) NFS0004ACONSULT-II MAIN FUNCTION CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.M/R OUTPUTActuator motor and motor relay status (ON/OFF)When actuator motor and motor relay are active (ACTIVE TEST with CON-SULT-II).ONBRC-121, "ABS Motor and Motor Relay System"When the actuator motor and motor relay are not operatingOFFFLUID LEV SWBrake fluid level sen-sor ON/OFF statusWhen brake fluid level sensor is onONBRC-127, "Brake Fluid Level Switch System"When the brake fluid level sen-sor is offOFFFAIL SIGNAL Fail signal statusDuring VDC fail-safeDuring TCS fail-safeDuring ABS fail-safeDuring EBD fail-safeONVDC systemTCS systemABS systemEBD systemMonitor item Display ContentData monitorReference: Inspection itemConditionReference values for normal opera-tionDiagnostic test mode Function ReferenceWORK SUPPORTThis mode enables a technician to adjust some devices faster and more accurately by following the indications on CONSULT-II.BRC-83, "Adjustment of Steering Angle Sensor Neutral Position"SELF-DIAG RESULTS Self-diagnostic results can be read and erased quickly. BRC-102, "Self-Diagnosis"DATA MONITORInput/Output data in the ABS actuator and electric unit (control unit) can be read.BRC-105, "Data Monitor"CAN DIAG SUPPORT MNTRThe results of transmit/receive diagnosis of communication can be read.LAN-15, "CAN Diagnostic Support Monitor"ACTIVE TESTDiagnostic Test Mode in which CONSULT-II drives some actuators apart from the ABS actuator and electric unit (control unit) and also shifts some parameters in a specified range.BRC-107, "Active Test"FUNCTION TESTConducted by CONSULT-II instead of a technician to determine whether each system is OK or NG.ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read.