Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 102

BRC-102
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2005 August 2006 350Z
Self-Diagnosis NFS000HK
DESCRIPTION
If an error is detected in the system, ABS warning lamp on the combination meter turn on. In this case, per-
form self-diagnosis as follows:
OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
3. Turn ignition switch ON.
4. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
5. After stopping the vehicle, with the engine running, touch ?START (NISSAN BASED VHCL)?, ?ABS?,
?SELF-DIAG RESULTS? in order on the CONSULT-II screen.
CAUTION:
If ?START (NISSAN BASED VHCL)? is touched immediately after starting the engine or turning on
the ignition switch, ?ABS? might not be displayed in the ?SELECT SYSTEM? screen. In this case,
repeat the operation from step 1.
6. The self-diagnostic results are displayed. (If necessary, the self-diagnostic results can be printed out by
touching ?PRINT?.)
? When ?NO FAILURE? is displayed, check the ABS warning lamp, VDC OFF indicator lamp, and SLIP
indicator lamp.
7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioning
component.
8. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
CAUTION:
? When a wheel sensor ?short-circuit? is detected, if the vehicle is not driven at 30 km/h (19 MPH)
for at least 1 minute, the ABS warning lamp will not turn off even if everything is normal.
ERASE MEMORY
1. Turn ignition switch OFF.
2. Start the engine and touch ?START (NISSAN BASED VHCL)?, ?ABS?, ?SELF-DIAG RESULTS?, ?ERASE
MEMORY? in order on the CONSULT-II screen to erase the error memory.
CAUTION:
If the error memory is not erased, re-conduct the operation from step 4.
3. Perform self-diagnosis again, and make sure that diagnostic memory is erased.
4. Drive vehicle at 30 km/h (19MPH) or more for approximately 1 minute as the final inspection, and make
sure that the ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp turn off.
NOTE:
VDC OFF switch should not stay ?ON? position.

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

BRC-102[VDC/TCS/ABS]TROUBLE DIAGNOSISRevision: 2005 August 2006 350ZSelf-Diagnosis NFS000HKDESCRIPTIONIf an error is detected in the system, ABS warning lamp on the combination meter turn on. In this case, per-form self-diagnosis as follows:OPERATION PROCEDURE1. Turn ignition switch OFF.2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.CAUTION:If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might bedetected in self-diagnosis depending on control unit which carry out CAN communication.3. Turn ignition switch ON.4. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.5. After stopping the vehicle, with the engine running, touch START (NISSAN BASED VHCL), ABS,SELF-DIAG RESULTS in order on the CONSULT-II screen.CAUTION:If START (NISSAN BASED VHCL) is touched immediately after starting the engine or turning onthe ignition switch, ABS might not be displayed in the SELECT SYSTEM screen. In this case,repeat the operation from step 1.6. The self-diagnostic results are displayed. (If necessary, the self-diagnostic results can be printed out bytouching PRINT.) When NO FAILURE is displayed, check the ABS warning lamp, VDC OFF indicator lamp, and SLIPindicator lamp.7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioningcomponent.8. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.CAUTION: When a wheel sensor short-circuit is detected, if the vehicle is not driven at 30 km/h (19 MPH)for at least 1 minute, the ABS warning lamp will not turn off even if everything is normal.ERASE MEMORY1. Turn ignition switch OFF.2. Start the engine and touch START (NISSAN BASED VHCL), ABS, SELF-DIAG RESULTS, ERASEMEMORY in order on the CONSULT-II screen to erase the error memory.CAUTION:If the error memory is not erased, re-conduct the operation from step 4.3. Perform self-diagnosis again, and make sure that diagnostic memory is erased.4. Drive vehicle at 30 km/h (19MPH) or more for approximately 1 minute as the final inspection, and makesure that the ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp turn off.NOTE:VDC OFF switch should not stay ON position.