Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 107

TROUBLE DIAGNOSIS
BRC-107
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
Revision: 2005 August 2006 350Z
: Applicable
?: Not applicable
Active Test NFS000IP
CAUTION:
? Do not perform active test while driving.
? Make sure to completely bleed air from the brake system.
? The ABS and brake warning lamps turn on during the active test.
OPERATION PROCEDURE
1. Connect the CONSULT-II and CONVERTER to the data link connector and start the engine.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
2. Touch ?START (NISSAN BASED VHCL) ? on the display screen.
3. Touch ?ABS?. If ABS is not indicated, go to GI-39, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Touch ?ACTIVE TEST?.
5. The test item selection screen is displayed.
6. Touch necessary test item.
7. With the ?MAIN ITEM? display shown in reverse, touch ?START?.
8. The ?ACTIVE TEST? screen will be displayed, so conduct the following test.
NOTE:
? When the active test is conducted while depressing the pedal, the pedal depression amount will change,
but this is normal.
ASCD SIGNAL
(ON/OFF)
? ? x ASCD (ON/OFF) status is displayed.
FLUID LEV
(ON/OFF)
x? x
Brake fluid level sensor (ON/OFF) status is dis-
played.
PARKING BRAKE SW
(ON/OFF)
x? x
Parking brake switch (ON/OFF) status is dis-
played.
USV FL-RR
(ON/OFF)
?? x
Primary side USV solenoid valve (ON/OFF)
status is displayed.
USV FR-RL
(ON/OFF)
?? x
Secondary side USV solenoid valve (ON/OFF)
status is displayed.
HSV FL-RR
(ON/OFF)
?? x
Primary side HSV solenoid valve (ON/OFF)
status is displayed.
HSV FR-RL
(ON/OFF)
?? x
Secondary side HSV solenoid valve (ON/OFF)
status is displayed.
V/R OUTPUT
(ON/OFF)
?? x
Valve relay operation signal (ON/OFF) status is
displayed.
M/R OUTPUT
(ON/OFF)
?? x
Monitor relay operation signal (ON/OFF) status
is displayed.
Item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
PFIA0301E

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

TROUBLE DIAGNOSISBRC-107[VDC/TCS/ABS]CDEGHIJKLMABBRCRevision: 2005 August 2006 350Z: Applicable: Not applicableActive Test NFS000IPCAUTION: Do not perform active test while driving. Make sure to completely bleed air from the brake system. The ABS and brake warning lamps turn on during the active test.OPERATION PROCEDURE1. Connect the CONSULT-II and CONVERTER to the data link connector and start the engine.CAUTION:If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might bedetected in self-diagnosis depending on control unit which carry out CAN communication.2. Touch START (NISSAN BASED VHCL) on the display screen.3. Touch ABS. If ABS is not indicated, go to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit" .4. Touch ACTIVE TEST.5. The test item selection screen is displayed.6. Touch necessary test item.7. With the MAIN ITEM display shown in reverse, touch START.8. The ACTIVE TEST screen will be displayed, so conduct the following test.NOTE: When the active test is conducted while depressing the pedal, the pedal depression amount will change,but this is normal.ASCD SIGNAL (ON/OFF) x ASCD (ON/OFF) status is displayed.FLUID LEV (ON/OFF)x xBrake fluid level sensor (ON/OFF) status is dis-played.PARKING BRAKE SW (ON/OFF)x xParking brake switch (ON/OFF) status is dis-played.USV FL-RR (ON/OFF) xPrimary side USV solenoid valve (ON/OFF) status is displayed.USV FR-RL (ON/OFF) xSecondary side USV solenoid valve (ON/OFF) status is displayed.HSV FL-RR (ON/OFF) xPrimary side HSV solenoid valve (ON/OFF) status is displayed.HSV FR-RL (ON/OFF) xSecondary side HSV solenoid valve (ON/OFF) status is displayed.V/R OUTPUT (ON/OFF) xValve relay operation signal (ON/OFF) status is displayed.M/R OUTPUT (ON/OFF) xMonitor relay operation signal (ON/OFF) status is displayed.Item (Unit)SELECT MONITOR ITEMRemarksECU INPUT SIGNALSMAIN SIGNALSSELECTION FROM MENUPFIA0301E