Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 55

TROUBLE DIAGNOSIS
BRC-55
[TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
Revision: 2005 August 2006 350Z
CONSULT- II Functions (TCS/ABS) NFS00035
CONSULT-II MAIN FUNCTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II
CONVERTER, malfunctions might be detected in self-diag-
nosis depending on control unit which carry out CAN com-
munication.
3. Turn ignition switch ON.
4. Touch ?START (NISSAN BASED VHCL)?.
5. Touch ?ABS? in the ?SELECT SYSTEM? screen.
If ?ABS? is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
Diagnostic test mode Function Reference
SELF-DIAG RESULTS Self-diagnostic results can be read and erased quickly. BRC-56, "
Self-diagnosis"
DATA MONITOR
Input/Output data in the ABS actuator and electric unit (control unit)
can be read.
BRC-58, "
Data Monitor"
CAN DIAG SUPPORT
MNTR
The results of transmit/receive diagnosis of communication can be
read.
LAN-15, "CAN Diagnostic Sup-
port Monitor"
ACTIVE TEST
Diagnostic Test Mode in which CONSULT-II drives some actuators
apart from the ABS actuator and electric unit (control unit) and also
shifts some parameters in a specified range.
BRC-60, "Active Test"
FUNCTION TEST
Conducted by CONSULT-II instead of a technician to determine
whether each system is ?OK? or ?NG?.
?
ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read. ?
PBIB1069E
SKIA3098E
BCIA0030E

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

TROUBLE DIAGNOSISBRC-55[TCS/ABS]CDEGHIJKLMABBRCRevision: 2005 August 2006 350ZCONSULT- II Functions (TCS/ABS) NFS00035CONSULT-II MAIN FUNCTION CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.CONSULT-II BASIC OPERATION PROCEDURE1. Turn ignition switch OFF.2. Connect CONSULT-II and CONSULT-II CONVERTER to thedata link connector.CAUTION:If CONSULT-II is used with no connection of CONSULT-IICONVERTER, malfunctions might be detected in self-diag-nosis depending on control unit which carry out CAN com-munication.3. Turn ignition switch ON.4. Touch START (NISSAN BASED VHCL).5. Touch ABS in the SELECT SYSTEM screen.If ABS is not indicated, go to GI-39, "CONSULT-II Data LinkConnector (DLC) Circuit" .Diagnostic test mode Function ReferenceSELF-DIAG RESULTS Self-diagnostic results can be read and erased quickly. BRC-56, "Self-diagnosis"DATA MONITORInput/Output data in the ABS actuator and electric unit (control unit) can be read.BRC-58, "Data Monitor"CAN DIAG SUPPORT MNTRThe results of transmit/receive diagnosis of communication can be read.LAN-15, "CAN Diagnostic Sup-port Monitor"ACTIVE TESTDiagnostic Test Mode in which CONSULT-II drives some actuators apart from the ABS actuator and electric unit (control unit) and also shifts some parameters in a specified range.BRC-60, "Active Test"FUNCTION TESTConducted by CONSULT-II instead of a technician to determine whether each system is OK or NG.ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read. PBIB1069ESKIA3098EBCIA0030E