Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 56

BRC-56
[TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2005 August 2006 350Z
6. Select the required diagnostic location from the ?SELECT SYS-
TEM? screen.
For further information, see the CONSULT-II Operation Manual.
Self-diagnosis NFS000HG
DESCRIPTION
If an error is detected in the system, ABS warning lamp, TCS OFF indicator lamp and SLIP indicator lamp on
the combination meter turn on. In this case, perform self-diagnosis as follows:
OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
3. Turn ignition switch ON.
4. Start engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
5. After stopping the vehicle, with the engine running, touch ?START (NISSAN BASED VHCL)?, ?ABS?,
?SELF-DIAG RESULTS? in order on the CONSULT-II screen.
CAUTION:
If ?START (NISSAN BASED VHCL)? is touched immediately after starting the engine or turning on
the ignition switch, ?ABS? might not be displayed in the ?SELECT SYSTEM? screen. In this case,
repeat the operation from step 1.
6. The self-diagnostic results are displayed. (If necessary, the self-diagnostic results can be printed out by
touching ?PRINT?.)
? When ?NO FAILURE? is displayed, check the ABS warning lamp, TCS OFF indicator lamp, and SLIP
indicator lamp.
7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioning
component.
8. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
CAUTION:
? When a wheel sensor ?short-circuit? is detected, if the vehicle is not driven at 30 km/h (19 MPH)
or more for at least 1 minute, the ABS warning lamp will not turn off even if everything is normal.
ERASE MEMORY
1. Turn ignition switch OFF.
2. Start the engine and touch ?START (NISSAN BASED VHCL)?, ?ABS?, ?SELF-DIAG RESULTS?, ?ERASE
MEMORY? in order on the CONSULT-II screen to erase the error memory.
CAUTION:
If the error memory is not erased, re-conduct the operation from step 4.
3. Perform self-diagnosis again, and make sure that diagnostic memory is erased.
4. Drive vehicle at 30 km/h (19MPH) or more for approximately 1 minute as the final inspection, and make
sure that the ABS warning lamp, TCS OFF indicator lamp and SLIP indicator lamp turn OFF.
NOTE:
TCS OFF switch should not stay ?ON? position.
BCIA0031E

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

BRC-56[TCS/ABS]TROUBLE DIAGNOSISRevision: 2005 August 2006 350Z6. Select the required diagnostic location from the SELECT SYS-TEM screen.For further information, see the CONSULT-II Operation Manual.Self-diagnosis NFS000HGDESCRIPTIONIf an error is detected in the system, ABS warning lamp, TCS OFF indicator lamp and SLIP indicator lamp onthe combination meter turn on. In this case, perform self-diagnosis as follows:OPERATION PROCEDURE1. Turn ignition switch OFF.2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.CAUTION:If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might bedetected in self-diagnosis depending on control unit which carry out CAN communication.3. Turn ignition switch ON.4. Start engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.5. After stopping the vehicle, with the engine running, touch START (NISSAN BASED VHCL), ABS,SELF-DIAG RESULTS in order on the CONSULT-II screen.CAUTION:If START (NISSAN BASED VHCL) is touched immediately after starting the engine or turning onthe ignition switch, ABS might not be displayed in the SELECT SYSTEM screen. In this case,repeat the operation from step 1.6. The self-diagnostic results are displayed. (If necessary, the self-diagnostic results can be printed out bytouching PRINT.) When NO FAILURE is displayed, check the ABS warning lamp, TCS OFF indicator lamp, and SLIPindicator lamp.7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioningcomponent.8. Start the engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.CAUTION: When a wheel sensor short-circuit is detected, if the vehicle is not driven at 30 km/h (19 MPH)or more for at least 1 minute, the ABS warning lamp will not turn off even if everything is normal.ERASE MEMORY1. Turn ignition switch OFF.2. Start the engine and touch START (NISSAN BASED VHCL), ABS, SELF-DIAG RESULTS, ERASEMEMORY in order on the CONSULT-II screen to erase the error memory.CAUTION:If the error memory is not erased, re-conduct the operation from step 4.3. Perform self-diagnosis again, and make sure that diagnostic memory is erased.4. Drive vehicle at 30 km/h (19MPH) or more for approximately 1 minute as the final inspection, and makesure that the ABS warning lamp, TCS OFF indicator lamp and SLIP indicator lamp turn OFF.NOTE:TCS OFF switch should not stay ON position.BCIA0031E