Nissan 350Z Workshop Maunual 2006 (9) PDF | Page 58

BRC-58
[TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2005 August 2006 350Z
Note 1: After completing repairs of the shorted sensor circuit, when ignition switch is turned ON, ABS warning lamp turns on. Check that
ABS warning lamp turns off while driving the vehicle at approximately 30 km/h (19 MPH) or more for approximately 1 minute according
to self-diagnosis procedure. In addition, if wheel sensor 2 is displayed for the wheels, check the wheel sensor circuit and also check the
control unit power voltage.
Note 2: When errors are detected in several systems, including the CAN communication system [U1000], troubleshoot the CAN commu-
nication system.
Data Monitor NFS000HH
OPERATION PROCEDURE
1. After turning OFF the ignition switch, connect CONSULT-II and the CONVERTER to the data link connec-
tor.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
2. Touch ?START (NISSAN BASED VHCL)?, ?ABS?, ?DATA MONITOR? in order on the CONSULT-II screen.
If ?ABS? is not indicated, go to GI-39, "
CONSULT-II Data Link Connector (DLC) Circuit" .
CAUTION:
When ?START (NISSAN BASED VHCL)? is touched immediately after starting the engine or turning
on the ignition switch, ?ABS? might not be displayed in the ?SELECT SYSTEM? screen. In this
case, repeat the operation from step 2.
3. Return to the ?SELECT MONITOR ITEM? screen, and touch?ECU INPUT SIGNALS? or ?MAIN SIGNALS?
or ?SELECTION FROM MENU?. Refer to the following information.
4. When ?START? is touched, the data monitor screen is displayed.
DISPLAY ITEM LIST
ENGINE SIGNAL 1
Major engine components are malfunctioning.
BRC-67, "
Engine Sys-
tem"
ENGINE SIGNAL 2
ENGINE SIGNAL 3
ENGINE SIGNAL 4
ENGINE SIGNAL 5
ENGINE SIGNAL 6
CAN COMM CIRCUIT When there is an error in the CAN communication system.
BRC-72, "
CAN Commu-
nication System"
(Note 2)
Display item Malfunction detecting condition Check item
Item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
FR LH SENSOR
[km/h (MPH)]
Wheel speed calculated by front LH wheel
sensor signal is displayed.
FR RH SENSOR
[(km/h (MPH)]
Wheel speed calculated by front RH wheel
sensor signal is displayed.
RR LH SENSOR
[km/h (MPH)]
Wheel speed calculated by Rear LH wheel
sensor signal is displayed.
RR RH SENSOR
[km/h (MPH)]
Wheel speed calculated by Rear RH wheel
sensor signal is displayed.
FR LH IN SOL
(ON/OFF)
?
Front left inlet ABS solenoid valve (ON/OFF)
status is displayed.
FR LH OUT SOL
(ON/OFF)
?
Front left outlet ABS solenoid valve (ON/
OFF) status is displayed.
RR RH IN SOL
(ON/OFF)
?
Rear right inlet ABS solenoid valve (ON/OFF)
status is displayed.
RR RH OUT SOL
(ON/OFF)
?
Rear right outlet ABS solenoid valve (ON/
OFF) status is displayed.

Nissan 350Z Workshop Maunual 2006 (9) Summary of Content

BRC-58[TCS/ABS]TROUBLE DIAGNOSISRevision: 2005 August 2006 350ZNote 1: After completing repairs of the shorted sensor circuit, when ignition switch is turned ON, ABS warning lamp turns on. Check thatABS warning lamp turns off while driving the vehicle at approximately 30 km/h (19 MPH) or more for approximately 1 minute accordingto self-diagnosis procedure. In addition, if wheel sensor 2 is displayed for the wheels, check the wheel sensor circuit and also check thecontrol unit power voltage.Note 2: When errors are detected in several systems, including the CAN communication system [U1000], troubleshoot the CAN commu-nication system.Data Monitor NFS000HHOPERATION PROCEDURE1. After turning OFF the ignition switch, connect CONSULT-II and the CONVERTER to the data link connec-tor.CAUTION:If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might bedetected in self-diagnosis depending on control unit which carry out CAN communication.2. Touch START (NISSAN BASED VHCL), ABS, DATA MONITOR in order on the CONSULT-II screen.If ABS is not indicated, go to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit" .CAUTION:When START (NISSAN BASED VHCL) is touched immediately after starting the engine or turningon the ignition switch, ABS might not be displayed in the SELECT SYSTEM screen. In thiscase, repeat the operation from step 2.3. Return to the SELECT MONITOR ITEM screen, and touchECU INPUT SIGNALS or MAIN SIGNALSor SELECTION FROM MENU. Refer to the following information.4. When START is touched, the data monitor screen is displayed.DISPLAY ITEM LISTENGINE SIGNAL 1Major engine components are malfunctioning.BRC-67, "Engine Sys-tem"ENGINE SIGNAL 2ENGINE SIGNAL 3ENGINE SIGNAL 4ENGINE SIGNAL 5ENGINE SIGNAL 6CAN COMM CIRCUIT When there is an error in the CAN communication system.BRC-72, "CAN Commu-nication System"(Note 2)Display item Malfunction detecting condition Check itemItem (Unit)SELECT MONITOR ITEMRemarksECU INPUT SIGNALSMAIN SIGNALSSELECTION FROM MENUFR LH SENSOR[km/h (MPH)]Wheel speed calculated by front LH wheel sensor signal is displayed.FR RH SENSOR[(km/h (MPH)]Wheel speed calculated by front RH wheel sensor signal is displayed.RR LH SENSOR [km/h (MPH)]Wheel speed calculated by Rear LH wheel sensor signal is displayed.RR RH SENSOR [km/h (MPH)]Wheel speed calculated by Rear RH wheel sensor signal is displayed.FR LH IN SOL(ON/OFF) Front left inlet ABS solenoid valve (ON/OFF) status is displayed.FR LH OUT SOL (ON/OFF) Front left outlet ABS solenoid valve (ON/OFF) status is displayed.RR RH IN SOL (ON/OFF) Rear right inlet ABS solenoid valve (ON/OFF) status is displayed.RR RH OUT SOL (ON/OFF) Rear right outlet ABS solenoid valve (ON/OFF) status is displayed.