Proton 300 Serie Workshop Manuals and Repair Manuals
Every Manual available online - found by our community and shared for FREE. Enjoy!
Proton 300 Serie
The Proton Satria is a hatchback produced by Malaysian Proton in 1994 for the first generation and ended in 2005. The new Satria Replacement Model (SRM), known as Proton Satria Neo was launched on 16 June 2006. The first generation Proton Satria, also marketed as the Proton Compact in the United Kingdom, and the Proton 300 Series in various European markets is a 3-door hatchback based on the fourth generation Mitsubishi Mirage / Colt. It was unveiled on 12 November 1994. The Proton Satria was initially available in three variants at launch with two engine options, namely the old 12-valve carburetted 1.3-litre 4G13P unit from the Proton Saga and a newer 16-valve multipoint fuel injected 1.6-litre 4G92P unit.Proton 300 Serie FAQ's
How do I check the brake fluid level in a Proton 300 Serie?
To check the brake fluid level in a Proton 300 Serie, locate the brake fluid reservoir, usually mounted on the firewall near the master cylinder. Ensure the vehicle is parked on a level surface and the engine is off. Remove the reservoir cap and visually inspect the fluid level, which should be between the minimum and maximum marks on the reservoir. If the fluid is below the minimum mark, add the recommended brake fluid to bring it within the acceptable range. Maintaining proper brake fluid level is essential for safe braking performance.
How do I check the coolant level in a Proton 300 Serie?
To check the coolant level in a Proton 300 Serie, ensure the engine is cool and the vehicle is parked on a level surface. Locate the coolant reservoir, usually positioned near the radiator. Remove the reservoir cap and visually inspect the coolant level, which should be between the minimum and maximum marks on the reservoir. If the level is low, add the appropriate coolant mixture recommended in the Proton 300 Serie automotive repair manual. Maintaining proper coolant level and quality is essential for preventing overheating and engine damage.
How do I check the tire pressure in a Proton 300 Serie?
To check the tire pressure in a Proton 300 Serie, use a tire pressure gauge to measure the pressure of each tire when they are cold (before driving). Unscrew the valve cap from each tire, press the gauge onto the valve stem, and read the pressure on the gauge. Compare the measured pressure to the recommended tire pressure indicated in the Proton 300 Serie automotive repair manual. If the pressure is low, add air until it reaches the recommended level. Proper tire pressure ensures optimal handling, fuel efficiency, and tire lifespan.
How do I check the transmission fluid level in a Proton 300 Serie?
To check the transmission fluid level in a Proton 300 Serie, start the engine and let it idle for a few minutes. Then, locate the transmission dipstick, which is usually labeled and located near the engine. Remove the dipstick, wipe it clean, reinsert it, and then remove it again to check the fluid level. Ensure that the fluid is within the designated range on the dipstick to ensure proper transmission function.
How do I replace a blown fuse in a Proton 300 Serie?
To replace a blown fuse in a Proton 300 Serie, locate the fuse box, usually found in the engine compartment or under the dashboard. Use the fuse diagram in the Proton 300 Serie automotive repair manual to identify the specific fuse related to the malfunctioning component. Once identified, use a fuse puller or needle-nose pliers to remove the blown fuse and replace it with a new one of the same rating. Properly functioning fuses are crucial for protecting electrical circuits and preventing damage.
How do I replace the brake pads in a Proton 300 Serie?
To replace the brake pads in a Proton 300 Serie, first, secure the vehicle on a level surface and engage the parking brake. Remove the wheel/tire assembly, then remove the caliper bolts and carefully lift the caliper off the brake rotor. Remove the old brake pads and install the new ones, ensuring they are correctly aligned and properly seated in the caliper brackets. Reinstall the caliper, tighten the bolts, and repeat the process for the other wheels. Properly functioning brake pads are crucial for safe braking and optimal stopping performance.
How do I replace the cabin air filter in a Proton 300 Serie?
To replace the cabin air filter in a Proton 300 Serie, locate the cabin air filter housing, which is usually located behind the glove compartment or under the dashboard. Open the housing, remove the old filter, and clean the housing if necessary. Insert the new filter into the housing, ensuring it is properly aligned, and close the housing. Regularly replacing the cabin air filter helps maintain clean and fresh air inside the vehicle's cabin.
How do I replace the headlights in a Proton 300 Serie?
To replace the headlights in a Proton 300 Serie, open the hood and locate the backside of the headlight assembly. Disconnect the electrical connector and remove the retaining screws or clips securing the headlight assembly. Carefully pull out the assembly, then disconnect the bulb socket and remove the old bulb. Insert the new bulb into the socket, reconnect the socket, and secure the headlight assembly back into place. Properly functioning headlights are crucial for visibility and safe nighttime driving.
How do I replace the serpentine belt in a Proton 300 Serie?
To replace the serpentine belt in a Proton 300 Serie, locate the belt routing diagram, usually found on a decal in the engine compartment. Use a wrench or tensioner tool to release the tension on the belt, then remove the old belt from the pulleys. Install the new belt, following the correct routing as per the diagram. Once the belt is properly installed, release the tensioner to apply proper tension. Regularly inspecting and replacing the serpentine belt ensures proper power distribution and prevents engine accessory failure.
How do I reset the maintenance light in a Proton 300 Serie?
To reset the maintenance light in a Proton 300 Serie, turn the ignition key to the "ON" position without starting the engine. Press and hold the trip odometer reset button until the maintenance light starts flashing. Release the button, turn off the ignition, and then start the engine. The maintenance light should now be reset, indicating that the maintenance interval has been successfully cleared.
How often should I replace the air filter in a Proton 300 Serie?
The air filter in a Proton 300 Serie should be replaced according to the manufacturer's recommended maintenance schedule, typically every 12,000 to 15,000 miles or as specified in the manual. However, if you frequently drive in dusty or polluted environments, it is advisable to inspect and replace the air filter more frequently. Regularly replacing the air filter ensures clean air intake, protects the engine from harmful debris, and promotes optimal fuel efficiency.
How often should I replace the spark plugs in a Proton 300 Serie?
The spark plugs in a Proton 300 Serie should be replaced according to the manufacturer's recommended maintenance schedule, typically every 30,000 to 50,000 miles or as specified in the manual. However, it is advisable to inspect the spark plugs regularly and replace them if they show signs of wear, such as erosion, excessive carbon buildup, or misfiring. Properly functioning spark plugs are essential for optimal engine performance and fuel efficiency.
What should I do if the Proton 300 Serie's battery is dead?
If the Proton 300 Serie's battery is dead, you can jump-start the vehicle using jumper cables and another vehicle with a charged battery. Connect the positive terminals of both batteries with the red jumper cable, then connect the negative terminal of the charged battery to a metal part of the dead vehicle. Start the engine of the charged vehicle and rev it slightly, then attempt to start the Proton 300 Serie. Once started, let the engine run for a while to recharge the battery.
What should I do if the Proton 300 Serie's check engine light comes on?
If the Proton 300 Serie's check engine light comes on, it indicates a potential issue with the vehicle's engine or emissions system. It is recommended to have the vehicle checked by a qualified mechanic or use an OBD-II scanner to retrieve the diagnostic trouble codes (DTCs) associated with the check engine light. Once the DTCs are obtained, refer to the Proton 300 Serie automotive repair manual for a detailed troubleshooting guide to address the specific issue.
What type of engine oil should I use in a Proton 300 Serie?
The recommended engine oil for a Proton 300 Serie is typically a multi-grade oil with the appropriate viscosity specified by the manufacturer. Refer to the Proton 300 Serie automotive repair manual for the exact viscosity and oil specifications. It is crucial to use the recommended oil to optimize engine performance, ensure proper lubrication, and maintain the vehicle's warranty.
Get notified for new manuals?
We'll send you a quick email when a new Proton 300 Serie manual is added.
There are currently no manuals available for Proton 300 Serie at this time.