Subaru Forester Body Electrical System 1999 2000 (1) PDF

1. Combination Meter
A: DIAGNOSTICS PROCEDURE
If speedometer does not operate, or operates
abnormally, check combination meter circuit.
CAUTION:
Make sure that trouble code of vehicle speed
sensor system appears in electrical system on-
board diagnosis.
1A1 : CHECK POWER SUPPLY FOR COM-
BINATION METER.
1) Remove combination meter. <Ref. to 6-2
[W8A0].>
2) Turn ignition switch to ON.
3) Measure voltage between combination meter
connector and chassis ground.
Connector & terminal
(i10) No. 1 (+) ? Chassis ground (?):
S6M0430A
:
Is the voltage more than 10 V?
: Go to step 1A2.
: Repair harness and connector.
NOTE:
In this case, repair the following:
Open circuit in harness between combination
meter and battery.
Poor contact in coupling connectors (i10) and
combination meter connector. <Ref. to FORE-
WORD [W3C0].>
1A2 : CHECK POWER SUPPLY FOR COM-
BINATION METER.
Measure voltage between combination meter con-
nector and chassis ground.
Connector & terminal
(i10) No. 2 (+) ? Chassis ground (?):
S6M0431A
:
Is the voltage more than 10 V?
: Go to step 1A3.
: Repair harness and connector.
NOTE:
In this case, repair the following:
Open circuit in harness between combination
meter and battery.
Poor contact in coupling connectors (i10) and
combination meter connector. <Ref. to FORE-
WORD [W3C0].>
1A3 : CHECK GROUND CIRCUIT OF COM-
BINATION METER.
1) Turn ignition switch to OFF.
2) Measure resistance of harness between com-
bination meter connector and chassis ground.
Connector & terminal
(i10) No. 3 (+) ? Chassis ground (?):
S6M0432A
:
Is the resistance less than 10
?
?
: Go to step 1A4.
: Repair harness and connector.
2
6-2 [T1A0] DIAGNOSTICS
1. Combination Meter

Subaru Forester Body Electrical System 1999 2000 (1) Summary of Content

1. Combination MeterA: DIAGNOSTICS PROCEDUREIf speedometer does not operate, or operatesabnormally, check combination meter circuit.CAUTION:Make sure that trouble code of vehicle speedsensor system appears in electrical system on-board diagnosis.1A1 : CHECK POWER SUPPLY FOR COM-BINATION METER.1) Remove combination meter. Ref. to 6-2[W8A0].2) Turn ignition switch to ON.3) Measure voltage between combination meterconnector and chassis ground.Connector terminal(i10) No. 1 (+) Chassis ground ():S6M0430A:Is the voltage more than 10 V?: Go to step 1A2.: Repair harness and connector.NOTE:In this case, repair the following: Open circuit in harness between combinationmeter and battery. Poor contact in coupling connectors (i10) andcombination meter connector. Ref. to FORE-WORD [W3C0].1A2 : CHECK POWER SUPPLY FOR COM-BINATION METER.Measure voltage between combination meter con-nector and chassis ground.Connector terminal(i10) No. 2 (+) Chassis ground ():S6M0431A:Is the voltage more than 10 V?: Go to step 1A3.: Repair harness and connector.NOTE:In this case, repair the following: Open circuit in harness between combinationmeter and battery. Poor contact in coupling connectors (i10) andcombination meter connector. Ref. to FORE-WORD [W3C0].1A3 : CHECK GROUND CIRCUIT OF COM-BINATION METER.1) Turn ignition switch to OFF.2) Measure resistance of harness between com-bination meter connector and chassis ground.Connector terminal(i10) No. 3 (+) Chassis ground ():S6M0432A:Is the resistance less than 10?: Go to step 1A4.: Repair harness and connector.26-2 [T1A0] DIAGNOSTICS1. Combination Meter