Subaru Forester Brakes 1999 2000 (34) PDF

E: INSTALLATION
1) Install ABSCM&H/U.
CAUTION:
Confirm that the specifications of the
ABSCM&H/U conforms to the vehicle specifica-
tions.
Tightening torque:
18
5 Nm (1.8
0.5 kg-m, 13.0
3.6 ft-lb)
2) Install ABSCM&H/U ground terminal to bracket.
Tightening torque:
32
10 Nm (3.3
1.0 kg-m, 24
7 ft-lb)
3) Connect brake pipes to their correct
ABSCM&H/U connections. <Ref. to 4-4 [W16B0].>
B4M1222
4) Using cable clip, secure ABSCM&H/U harness
to bracket.
5) Connect connector to ABSCM&H/U.
CAUTION:
Be sure to remove all foreign matter from
inside the connector before connecting.
Ensure that the ABSCM&H/U connetor is
securely locked.
6) Install air intake duct.
7) Connect ground cable to battery.
8) Bleed air from the brake system.
15. G Sensor
A: REMOVAL AND INSTALLATION
1) Turn ignition switch to OFF.
2) Remove console cover. <Ref. to 5-4 [W1A0].>
3) Disconnect connector from G sensor.
4) Remove G sensor from body.
H4M1324
5) Install in the reverse order of removal.
CAUTION:
Do not drop or bump G sensor.
B: INSPECTION WITH CIRCUIT
TESTER
15B1 : CHECK G SENSOR.
1) Turn ignition switch to OFF.
2) Remove G sensor from vehicle.
3) Connect connector to G sensor.
4) Turn ignition switch to ON.
5) Measure voltage between G sensor connector
terminals.
Connector & terminal
(P9) No. 2 (+) ? No. 3 (?)
H4M1325
:
Is the voltage 2.3
0.2 V when G sen-
sor is horizontal?
: Go to step 15B2.
: Replace G sensor.
55
[W15B1] 4-4SERVICE PROCEDURE
15. G Sensor

Subaru Forester Brakes 1999 2000 (34) Summary of Content

E: INSTALLATION1) Install ABSCMH/U.CAUTION:Confirm that the specifications of theABSCMH/U conforms to the vehicle specifica-tions.Tightening torque:185 Nm (1.80.5 kg-m, 13.03.6 ft-lb)2) Install ABSCMH/U ground terminal to bracket.Tightening torque:3210 Nm (3.31.0 kg-m, 247 ft-lb)3) Connect brake pipes to their correctABSCMH/U connections. Ref. to 4-4 [W16B0].B4M12224) Using cable clip, secure ABSCMH/U harnessto bracket.5) Connect connector to ABSCMH/U.CAUTION: Be sure to remove all foreign matter frominside the connector before connecting. Ensure that the ABSCMH/U connetor issecurely locked.6) Install air intake duct.7) Connect ground cable to battery.8) Bleed air from the brake system.15. G SensorA: REMOVAL AND INSTALLATION1) Turn ignition switch to OFF.2) Remove console cover. Ref. to 5-4 [W1A0].3) Disconnect connector from G sensor.4) Remove G sensor from body.H4M13245) Install in the reverse order of removal.CAUTION:Do not drop or bump G sensor.B: INSPECTION WITH CIRCUITTESTER15B1 : CHECK G SENSOR.1) Turn ignition switch to OFF.2) Remove G sensor from vehicle.3) Connect connector to G sensor.4) Turn ignition switch to ON.5) Measure voltage between G sensor connectorterminals.Connector terminal(P9) No. 2 (+) No. 3 ()H4M1325:Is the voltage 2.30.2 V when G sen-sor is horizontal?: Go to step 15B2.: Replace G sensor.55[W15B1] 4-4SERVICE PROCEDURE15. G Sensor