Subaru Forester Brakes 1999 2000 (9) PDF

9. Select Monitor Function
Mode
Applicable cartridge of select monitor. <Ref. to 1-6
[G1100].>
NOTE:
For basic handling of the select monitor, refer to its
Operation Manual.
A: LIST OF FUNCTION MODE
1. ANALOG DATA ARE DISPLAYED
Display screen Contents to be monitored
FR wheel speed
Wheel speed detected by the Front
Right ABS sensor is displayed in km/h
or mile/h.
FL wheel speed
Wheel speed detected by the Front
Left ABS sensor is displayed in km/h
or mile/h.
RR wheel speed
Wheel speed detected by the Rear
Right ABS sensor is displayed in km/h
or mile/h.
RL wheel speed
Wheel speed detected by the Rear Left
ABS sensor is displayed in km/h or
mile/h.
Stop light switch
Stop light switch monitor voltage is dis-
played.
G sensor output
voltage
Refers to vehicle acceleration detecting
by the analog G sensor. It appears on
the select monitor display in volts.
2. ON/OFF DATA ARE DISPLAYED
Display screen Contents to be monitored
Stop light switch Stop light switch signal
Valve relay signal Valve relay signal
Motor relay sig-
nal
Motor relay signal
ABS signal to
TCM
ABS operation signal from ABS control
module to TCM
ABS warning
light
ABS warning light
Valve relay moni-
tor
Valve relay operation monitor signal
Motor relay moni-
tor
Motor relay operation monitor signal
CCM signal
ABS operation signal from ABS control
module to TCM (ABS operation signal
monitor)
3. TROUBLE CODES ARE DISPLAYED
A maximum of 3 trouble codes are displayed in
order of occurrence.
If a particular trouble code is not properly stored
in memory (due to a drop in ABSCM&H/U power
supply, etc.) when a problem occurs, the trouble
code, followed by a question mark ???, appears on
the select monitor display. This shows it may be an
unreliable reading.
S4M0076A
*a* refers to the troubles in order of occurrence
(Latest, Old, Older and Reference).
Display screen Contents to be monitored
Latest
The most recent trouble code appears
on the select monitor display.
Old
The second most recent trouble code
appears on the select monitor display.
Older
The third most recent trouble code
appears on the select monitor display.
Reference
A specified period of time proceeding
trouble code appears on the select
monitor display.
4. CLEAR MEMORY
Display screen Contents to be monitored
Clear memory?
Function of clearing trouble code and
freeze frame data.
5. ABS SEQUENCE CONTROL
Display
screen
Contents to be monitored Ref. to
ABS
sequence
control
Perform ABS sequence con-
trol by operating valve and
pump motor sequentially.
<Ref. to 4-4
[W14D2].>
78
4-4 [T900] DIAGNOSTICS
9. Select Monitor Function Mode

Subaru Forester Brakes 1999 2000 (9) Summary of Content

9. Select Monitor FunctionModeApplicable cartridge of select monitor. Ref. to 1-6[G1100].NOTE:For basic handling of the select monitor, refer to itsOperation Manual.A: LIST OF FUNCTION MODE1. ANALOG DATA ARE DISPLAYEDDisplay screen Contents to be monitoredFR wheel speedWheel speed detected by the FrontRight ABS sensor is displayed in km/hor mile/h.FL wheel speedWheel speed detected by the FrontLeft ABS sensor is displayed in km/hor mile/h.RR wheel speedWheel speed detected by the RearRight ABS sensor is displayed in km/hor mile/h.RL wheel speedWheel speed detected by the Rear LeftABS sensor is displayed in km/h ormile/h.Stop light switchStop light switch monitor voltage is dis-played.G sensor outputvoltageRefers to vehicle acceleration detectingby the analog G sensor. It appears onthe select monitor display in volts.2. ON/OFF DATA ARE DISPLAYEDDisplay screen Contents to be monitoredStop light switch Stop light switch signalValve relay signal Valve relay signalMotor relay sig-nalMotor relay signalABS signal toTCMABS operation signal from ABS controlmodule to TCMABS warninglightABS warning lightValve relay moni-torValve relay operation monitor signalMotor relay moni-torMotor relay operation monitor signalCCM signalABS operation signal from ABS controlmodule to TCM (ABS operation signalmonitor)3. TROUBLE CODES ARE DISPLAYEDA maximum of 3 trouble codes are displayed inorder of occurrence. If a particular trouble code is not properly storedin memory (due to a drop in ABSCMH/U powersupply, etc.) when a problem occurs, the troublecode, followed by a question mark ?, appears onthe select monitor display. This shows it may be anunreliable reading.S4M0076A *a* refers to the troubles in order of occurrence(Latest, Old, Older and Reference).Display screen Contents to be monitoredLatestThe most recent trouble code appearson the select monitor display.OldThe second most recent trouble codeappears on the select monitor display.OlderThe third most recent trouble codeappears on the select monitor display.ReferenceA specified period of time proceedingtrouble code appears on the selectmonitor display.4. CLEAR MEMORYDisplay screen Contents to be monitoredClear memory?Function of clearing trouble code andfreeze frame data.5. ABS SEQUENCE CONTROLDisplayscreenContents to be monitored Ref. toABSsequencecontrolPerform ABS sequence con-trol by operating valve andpump motor sequentially.Ref. to 4-4[W14D2].784-4 [T900] DIAGNOSTICS9. Select Monitor Function Mode