Subaru Forester Engine Electrical System 1999 2000 (7) PDF

(3) Set a new bearing and closely install a fit
tool on the bearing outer race. Press the bear-
ing down into place with a hand press or vise.
A socket wrench can serve as the tool.
(4) Install front bearing retainer.
S6M0410A
(A) Bearing
(B) Socket wrench
(C) Front bracket
D: ASSEMBLY
Assemble in the reverse order of disassembly.
1) Pulling up brush
Before assembling, press the brush down into the
brush holder with your finger and secure in that
position by passing a [2 mm (0.08 in) dia. length 4
to 5 cm (1.6 to 2.0 in)] wire (A) through the hole
shown in the figure.
CAUTION:
Be sure to remove the wire after reassembly.
S6M0411A
2) Heat the bearing box in the rear bracket [50 to
60C (122 to 140F)] and press the rear bearing
into the rear bracket.
CAUTION:
Grease should not be applied for the rear bear-
ing. Remove oil completely if it is found on the
bearing box.
3) After reassembly, turn the pulley by hand to
check that the rotor turns smoothly.
3. Spark Plug
A: REMOVAL AND INSTALLATION
CAUTION:
All spark plugs installed on an engine, must be
of the same heat range.
Spark plug:
CHAMPION: RC10YC4
(Alternate)
CHAMPION: RC8YC4
NGK: BKR6E-11
NIPPONDENSO: K20PR-U11
1. #1 SPARK PLUG
1) Disconnect battery ground cable.
G6M0095
2) Remove air intake duct and resonator chamber.
(1) Remove bolt which installs air intake duct
on the front side of body.
S6M0708
(2) Remove bolt which installs air intake duct
on body.
B2M2284
16
6-1 [W2D0] SERVICE PROCEDURE
3. Spark Plug

Subaru Forester Engine Electrical System 1999 2000 (7) Summary of Content

(3) Set a new bearing and closely install a fittool on the bearing outer race. Press the bear-ing down into place with a hand press or vise.A socket wrench can serve as the tool.(4) Install front bearing retainer.S6M0410A(A) Bearing(B) Socket wrench(C) Front bracketD: ASSEMBLYAssemble in the reverse order of disassembly.1) Pulling up brushBefore assembling, press the brush down into thebrush holder with your finger and secure in thatposition by passing a [2 mm (0.08 in) dia. length 4to 5 cm (1.6 to 2.0 in)] wire (A) through the holeshown in the figure.CAUTION:Be sure to remove the wire after reassembly.S6M0411A2) Heat the bearing box in the rear bracket [50 to60C (122 to 140F)] and press the rear bearinginto the rear bracket.CAUTION:Grease should not be applied for the rear bear-ing. Remove oil completely if it is found on thebearing box.3) After reassembly, turn the pulley by hand tocheck that the rotor turns smoothly.3. Spark PlugA: REMOVAL AND INSTALLATIONCAUTION:All spark plugs installed on an engine, must beof the same heat range.Spark plug:CHAMPION: RC10YC4(Alternate)CHAMPION: RC8YC4NGK: BKR6E-11NIPPONDENSO: K20PR-U111. #1 SPARK PLUG1) Disconnect battery ground cable.G6M00952) Remove air intake duct and resonator chamber.(1) Remove bolt which installs air intake ducton the front side of body.S6M0708(2) Remove bolt which installs air intake ducton body.B2M2284166-1 [W2D0] SERVICE PROCEDURE3. Spark Plug